CY8CLED04D01 Datasheet, PDF (29/52 Pages) Cypress Semiconductor – PowerPSoC Intelligent LED Driver

CY8CLED04D01, CY8CLED04D02
CY8CLED04G01, CY8CLED03D01
CY8CLED03D02, CY8CLED03G01
CY8CLED02D01, CY8CLED01D01
14. Electrical Specifications
This section presents the DC and AC electrical specifications of the CY8CLED04D0X, CY8CLED04G01, CY8CLED03D0X,
CY8CLED03G01, CY8CLED02D01, and CY8CLED01D01 of the PowerPSoC device family. For the most up to date electrical speci-
fications, confirm that you have the most recent data sheet by going to the web at http://www.cypress.com/psoc. Specifications are
valid for -40°C ≤ T_A ≤ 85°C and T_J ≤ 115°C, except where noted. Table 14-1 lists the units of measure that are used in this section.
Table 14-1. Units of Measure
Symbol
°C
dB
Hz
pp
σ
V
Ω
KB
ppm
sps
W
Unit of Measure
degrees Celsius
decibels
Hertz
peak-to-peak
sigma:one standard deviation
volts
ohms
1024 bytes
parts per million
samples per second
watts
A amperes
Symbol
Kbit
KHz
KΩ
MHz
MΩ
μA
μF
μH
μs
μV
μVrms
μW
Unit of Measure
1024 bits
kilohertz
kilohms
megahertz
megaohms
microamperes
microfarads
microhenrys
microseconds
microvolts
microvolts
root-mean-square
microwatts
Symbol
mA
ms
mV
mW
nA
ns
nV
pA
pF
ps
fF
Unit of Measure
milliampere
millisecond
millivolts
milliwatts
nanoamperes
nanoseconds
nanovolts
picoamperes
picofarads
picoseconds
femtofarads
14.1 Absolute Maximum Ratings
Exceeding maximum ratings may shorten the useful life of the device. Not all user guidelines are production tested.
Symbol
Description
Min Typ
Max Units
Notes
T_STG
Storage Temperature
-55
–
+115
°C Higher storage temperatures
reduces data retention time.
Recommended storage temper-
ature is 0°C to 50°C.
T_A
Ambient Temperature with Power Applied -40
–
VDD,
Supply Voltage on VDD, AVDD, GDVDD -0.5
–
AVDD,
GDVDD
+85
+6.0
°C T_J ≤ 115°C
V Relative to VSS, AVSS, and
GDVSS respectively
V_IO
DC Input Voltage
VSS - 0.5 – VDD + 0.5 V Applies only to GPIO and FN0
pins
V_IO2
V_FET
DC Voltage Applied to Tri-state
VSS - 0.5 – VDD + 0.5 V
Maximum Voltage from Power Switch
–
–
36 ^[2]
V PGNDx is connected to GDVSS
(SWx) to Power FET Ground (PGNDx)
V_CSP,V_CSN Maximum Voltage applied to CSA pins
-0.5
–
36 ^[2]
V
V_SENSE
Maximum Input Differential Voltage
across CSA input
-1.0
–
1.0
V
I_MAIO
Maximum Current into any Port Pin
Configured as Analog Driver
-50
–
+50
mA
I_MIO
Maximum Current into any Port and
Function Pin
-25
–
+50
mA
Note
2. Stresses beyond the “Absolute Maximum Ratings” may cause permanent damage to the device. The system designer must ensure that the Absolute Maximum Ratings
are NEVER exceeded. Functional operation is not implied under any conditions beyond the “Electrical Characteristics”, listed page 27 onwards. Extended exposure
to “Absolute Maximum Ratings” may affect device reliability.
Document Number: 001-46319 Rev. *G
Page 29 of 52
[+] Feedback