CY8C22113_04 Datasheet, PDF (25/36 Pages) Cypress Semiconductor – PSoC™ Mixed Signal Array

CY8C22x13 Final Data Sheet
3. Electrical Specifications
3.4.3 AC Operational Amplifier Specifications
The following tables list guaranteed maximum and minimum specifications for the voltage and temperature ranges: 4.75V to 5.25V
and -40°C ≤ T_A ≤ 85°C, or 3.0V to 3.6V and -40°C ≤ T_A ≤ 85°C, respectively. Typical parameters apply to 5V and 3.3V at 25°C and
are for design guidance only or unless otherwise specified.
Note Settling times, slew rates, and gain bandwidth are based on the Analog Continuous Time PSoC block.
Table 3-17. 5V AC Operational Amplifier Specifications
Symbol
T_ROA
T_SOA
SR_ROA
SR_FOA
BW_OA
E_NOA
Description
Rising Settling Time from 80% of ∆V to 0.1% of ∆V (10 pF
load, Unity Gain)
Power = Low
Power = Low, Opamp Bias = High
Power = Medium
Power = Medium, Opamp Bias = High
Power = High
Power = High, Opamp Bias = High
Falling Settling Time from 20% of ∆V to 0.1% of ∆V (10 pF
load, Unity Gain)
Power = Low
Power = Low, Opamp Bias = High
Power = Medium
Power = Medium, Opamp Bias = High
Power = High
Power = High, Opamp Bias = High
Rising Slew Rate (20% to 80%)(10 pF load, Unity Gain)
Power = Low
Power = Low, Opamp Bias = High
Power = Medium
Power = Medium, Opamp Bias = High
Power = High
Power = High, Opamp Bias = High
Falling Slew Rate (20% to 80%)(10 pF load, Unity Gain)
Power = Low
Power = Low, Opamp Bias = High
Power = Medium
Power = Medium, Opamp Bias = High
Power = High
Power = High, Opamp Bias = High
Gain Bandwidth Product
Power = Low
Power = Low, Opamp Bias = High
Power = Medium
Power = Medium, Opamp Bias = High
Power = High
Power = High, Opamp Bias = High
Noise at 1 kHz (Power = Medium, Opamp Bias = High)
Min
–
–
–
–
–
–
–
–
–
–
–
–
0.15
1.7
6.5
0.01
0.5
4.0
0.75
3.1
5.4
–
Typ
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
200
Max
3.9
0.72
0.62
5.9
0.92
0.72
–
Units
µs
µs
µs
µs
µs
µs
µs
µs
µs
µs
µs
µs
V/µs
V/µs
V/µs
V/µs
V/µs
V/µs
V/µs
V/µs
V/µs
V/µs
V/µs
V/µs
MHz
MHz
MHz
MHz
MHz
MHz
nV/rt-Hz
Notes
Specification maximums for low power and
high opamp bias, medium power, and
medium power and high opamp bias levels
are between low and high power levels.
Specification maximums for low power and
high opamp bias, medium power, and
medium power and high opamp bias levels
are between low and high power levels.
Specification minimums for low power and
high opamp bias, medium power, and
medium power and high opamp bias levels
are between low and high power levels.
Specification minimums for low power and
high opamp bias, medium power, and
medium power and high opamp bias levels
are between low and high power levels.
Specification minimums for low power and
high opamp bias, medium power, and
medium power and high opamp bias levels
are between low and high power levels.
June 3, 2004
Document No. 38-12009 Rev. *E
25