Z9972 Datasheet, PDF (2/9 Pages) Cypress Semiconductor – 3.3V, 125-MHz, Multi-Output Zero Delay Buffer

Z9972
Pin Descriptions
Pin
Name
PWR I/O Type
Description
11
XIN
I
Oscillator Input. Connect to a crystal.
12
XOUT
O
Oscillator Output. Connect to a crystal.
9
TCLK0
I PU External Reference/Test Clock Input.
10
TCLK1
I PU External Reference/Test Clock Input.
44, 46, 48, 50 QA(3:0) VDDC O
Clock Outputs. See Table 2 for frequency selections.
32, 34, 36, 38 QB(3:0) VDDC O
Clock Outputs. See Table 2 for frequency selections.
16, 18, 21, 23 QC(3:0) VDDC O
Clock Outputs. See Table 2 for frequency selections.
29
FB_OUT VDDC O
Feedback Clock Output. Connect to FB_IN for normal operation. The
divider ratio for this output is set by FB_SEL(0:2). See Table 1. A bypass
delay capacitor at this output will control Input Reference/ Output Banks
phase relationships.
25
SYNC
VDDC O
Synchronous Pulse Output. This output is used for system synchroni-
zation. The rising edge of the output pulse is in sync with both the rising
edges of QA (0:3) and QC(0:3) output clocks regardless of the divider
ratios selected.
42, 43
SELA(1,0)
I PU Frequency Select Inputs. These inputs select the divider ratio at QA(0:3)
outputs. See Table 2.
40, 41
SELB(1,0)
I PU Frequency Select Inputs. These inputs select the divider ratio at QB(0:3)
outputs. See Table 2.
19, 20
SELC(1,0)
I PU Frequency Select Inputs. These inputs select the divider ratio at QC(0:3)
outputs. See Table 2.
5, 26, 27 FB_SEL(2:0)
I PU Feedback Select Inputs. These inputs select the divide ratio at FB_OUT
output. See Table 2.
52
VCO_SEL
I PU VCO Divider Select Input. When set LOW, the VCO output is divided by
2. When set HIGH, the divider is bypassed. See Table 1.
31
FB_IN
I PU Feedback Clock Input. Connect to FB_OUT for accessing the PLL.
6
PLL_EN
I PU PLL Enable Input. When asserted HIGH, PLL is enabled. And when
LOW, the phase-lock loop (PLL) is bypassed.
7
REF_SEL
I PU Reference Select Input. When HIGH, the crystal oscillator is selected.
And when LOW, TCLK (0,1) is the reference clock.
8
TCLK_SEL
I PU TCLK Select Input. When LOW, TCLK0 is selected and when HIGH
TCLK1 is selected.
2
MR#/OE
I PU Master Reset/Output Enable Input. When asserted LOW, resets all of
the internal flip-flops and also disables all of the outputs. When pulled
HIGH, releases the internal flip-flops from reset and enables all of the
outputs.
14
INV_CLK
I PU Inverted Clock Input. When set HIGH, QC(2,3) outputs are inverted.
When set LOW, the inverter is bypassed.
3
SCLK
I PU Serial Clock Input. Clocks data at SDATA into the internal register.
4
SDATA
17, 22, 28,
33,37, 45, 49
13
VDDC^[2]
VDD^[2]
I PU Serial Data Input. Input data is clocked to the internal register to
enable/disable individual outputs. This provides flexibility in power
management.
3.3V Power Supply for Output Clock Buffers.
3.3V Supply for PLL.
1, 15, 24, 30,
35, 39, 47, 51
VSS
Common Ground.
Note:
2. A bypass capacitor (0.1 µF) should be placed as close as possible to each positive power (< 0.2”). If these bypass capacitors are not close to the pins their
high-frequency filtering characteristics will be cancelled by the lead inductance of the traces.
Document #: 38-07088 Rev. *D
Page 2 of 9