CY2CC1910 Datasheet, PDF (2/8 Pages) Cypress Semiconductor – 1:10 Clock Fanout Buffer with Output Enable

COMLINK™ SERIES
CY2CC1910
Maximum Ratings^[1,2]
Storage Temperature: ................................–65°C to + 150°C
Ambient Temperature:................................... –40°C to +85°C
Supply Voltage to Ground Potential
V_CC .................................................................. –0.5V to 4.6V
Input ................................................................. –0.5V to 5.8V
Variable Output Impedance Control (VOI™)
Supply Voltage to Ground Potential
(Outputs only) ........................................... –0.5V to V_DD + 1V
DC Output Voltage.................................... –0.5V to V_DD + 1V
Power Dissipation........................................................ 0.75W
Pull Down
3.5
Pull Up
3.5
3
3
2.5
2.5
2
2
1.5
1.5
1
1
0.5
0.5
0
0
0.01
0.02
0.03
0.04
0.05
0.06
0.07
0.08
0.09
0.1
Iol (A)
0
-0.18
-0.16
-0.14
-0.12
-0.1
-0.08
-0.06
-0.04
-0.02
0
Ioh (A)
Vdd = 3.3 V
Vdd = 2.5 V
Vdd = 1.8 V
Vdd= 3.3 V
Figure 1. Output Voltage vs. Output Current (T_A = 25°C)
Vdd= 2.5 V
Vdd= 1.8 V
DC Electrical Characteristics @ 3.3V (see Figure 2)
Parameter
Description
Conditions
V_OH
V_OL
V_IH
V_IL
I_IH
I_IL
I_I
V_IK
I_OK
O_OFF
V_H
Output High Voltage
Output Low Voltage
Input High Voltage
Input Low Voltage
Input High Current
Input Low Current
Input High Current
Clamp Diode Voltage
Continuous Clamp Current
Power-down Disable
Input Hysteresis
V_DD = Min.,V_IN = V_IH or V_IL
V_DD = Min.,V_IN = V_IH or V_IL
Guaranteed Logic High Level
Guaranteed Logic Low Level
V_DD = Max.
V_DD = Max.
V_DD = Max.,V_IN = V_DD(Max.)
V_DD = Min., I_IN = –18 mA
V_DD = Max.,V_OUT = GND
V_DD = GND,V_OUT = < 4.5V
DC Electrical Characteristics @ 2.5V (see Figure 2)
I_OH = –12 mA
I_OL = 12 mA
V_IN = 2.7V
V_IN = 0.5V
Min.
2.3
2
Typ.
3.3
0.2
–0.7
80
Max.
0.5
5.8
0.8
1
–1
20
–1.2
–50
100
Unit
V
V
V
V
uA
uA
uA
V
mA
uA
mV
Parameter
Description
Conditions
Min. Typ. Max. Unit
V_OH
Output High Voltage
V_DD = Min.,V_IN = V_IH or V_IL
V_DD = Min.,V_IN = V_IH or V_IL
I_OH = –7 mA 1.8
I_OH = 12 mA 1.6
V
V
V_OL
Output Low Voltage
Guaranteed Logic High Level I_OL = 12 mA
0.65
V
V_IH
Input High Voltage
Guaranteed Logic Low Level
1.6
5.0
V
V_IL
Input Low Voltage
V_DD = Max.
0.8
V
I_IH
Input High Current
V_DD = Max.
V_IN = 2.4V
1
uA
I_IL
Input Low Current
V_DD = Max.,V_IN = V_DD(Max.)
V_IN = 0.5V
–1
uA
I_I
Input High Current
V_DD = Min., I_IN = –18 mA
20
uA
V_IK
Clamp Diode Voltage
V_DD = Max.,V_OUT = GND
–0.7 –1.2
V
I_OK
Continuous Clamp Current V_DD = GND, V_OUT = < 4.5V
–50 mA
O_OFF
Power-down Disable
V_DD = Min.,V_IN = V_IH or V_IL
100 uA
V_H
Input Hysteresis
80
mV
Note:
1. Multiple Supplies: The Voltage on any input or I/O pin cannot exceed the power pin during power-up. Power supply sequencing is NOT required.
2. Stresses greater than those listed under absolute maximum ratings may cause permanent damage to the device. This is intended to be a stress rating only
and functional operation of the device at these or any other conditions above those indicated in the operation sections of this specification is not implied.
Exposure to absolute maximum rating conditions for extended periods may affect reliability.
Document #: 38-07347 Rev. *B
Page 2 of 8