CY7C1416AV18 Datasheet, PDF (1/24 Pages) Cypress Semiconductor – 36-Mbit DDR-II SRAM 2-Word Burst Architecture

PRELIMINARY
CY7C1416AV18
CY7C1427AV18
CY7C1418AV18
CY7C1420AV18
Features
• 36-Mbit density (4M x 8, 4M x 9, 2M x 18, 1M x 36)
• 250-MHz clock for high bandwidth
• 2-Word burst for reducing address bus frequency
• Double Data Rate (DDR) interfaces
(data transferred at 500 MHz) @ 250 MHz
• Two input clocks (K and K) for precise DDR timing
— SRAM uses rising edges only
• Two output clocks (C and C) account for clock skew
and flight time mismatching
• Echo clocks (CQ and CQ) simplify data capture in
high-speed systems
• Synchronous internally self-timed writes
• 1.8V core power supply with HSTL inputs and outputs
• Variable drive HSTL output buffers
• Expanded HSTL output voltage (1.4V–V_DD)
• 15 x 17 x 1.4 mm 1.0-mm pitch fBGA package,
165 ball (11x15 matrix)
• JTAG 1149.1 compatible test access port
• Delay Lock Loop (DLL) for accurate data placement
Configurations
CY7C1416AV18 – 4M x 8
CY7C1427AV18 – 4M x 9
CY7C1418AV18 – 2M x 18
CY7C1420AV18 – 1M x 36
36-Mbit DDR-II SRAM 2-Word
Burst Architecture
Functional Description
The CY7C1416AV18, CY7C1427AV18, CY7C1418AV18, and
CY7C1420AV18 are 1.8V Synchronous Pipelined SRAM
equipped with DDR-II architecture. The DDR-II consists of an
SRAM core with advanced synchronous peripheral circuitry
and a 1-bit burst counter. Addresses for Read and Write are
latched on alternate rising edges of the input (K) clock. Write
data is registered on the rising edges of both K and K. Read
data is driven on the rising edges of C and C if provided, or on
the rising edge of K and K if C/C are not provided. Each
address location is associated with two 8-bit words in the case
of CY7C1416AV18 and two 9-bit words in the case of
CY7C1427AV18 that burst sequentially into or out of the
device. The burst counter always starts with a “0” internally in
the case of CY7C1416AV18 and CY7C1427AV18. On
CY7C1418AV18 and CY7C1420AV18, the burst counter takes
in the least significant bit of the external address and bursts
two 18-bit words in the case of CY7C1418AV18 and two 36-bit
words in the case of CY7C1420AV18 sequentially into or out
of the device.
Asynchronous inputs include impedance match (ZQ).
Synchronous data outputs (Q, sharing the same physical pins
as the data inputs D) are tightly matched to the two output echo
clocks CQ/CQ, eliminating the need for separately capturing
data from each individual DDR SRAM in the system design.
Output data clocks (C/C) enable maximum system clocking
and data synchronization flexibility.
All synchronous inputs pass through input registers controlled
by the K or K input clocks. All data outputs pass through output
registers controlled by the C or C input clocks. Writes are
conducted with on-chip synchronous self-timed write circuitry.
Selection Guide
Maximum Operating Frequency
Maximum Operating Current
Shaded areas contain advance information.
250 MHz
250
TBD
200 MHz
200
TBD
167 MHz
167
TBD
Unit
MHz
mA
Cypress Semiconductor Corporation • 3901 North First Street • San Jose, CA 95134 • 408-943-2600
Document Number: 38-05616 Rev. **
Revised July 15, 2004