CY7C1344F Datasheet, PDF (1/15 Pages) Cypress Semiconductor – 2-Mbit (64K x 36) Flow-Through Sync SRAM

CY7C1344F
2-Mbit (64K x 36) Flow-Through Sync SRAM
Features
• 64K x 36 common I/O
• 3.3V –5% and +10% core power supply (V_DD)
• 3.3V I/O supply (V_DDQ)
• Fast clock-to-output times
— 7.5 ns (117-MHz version)
— 8.0 ns (100-MHz version)
• Provide high-performance 2-1-1-1 access rate
• User-selectable burst counter supporting Intel^
Pentium^ interleaved or linear burst sequences
• Separate processor and controller address strobes
• Synchronous self-timed write
• Asynchronous output enable
• Supports 3.3V I/O level
• Offered in JEDEC-standard 100-pin TQFP package
• “ZZ” Sleep Mode option
Functional Description^[1]
The CY7C1344F is a 65,536 x 36 synchronous cache RAM
designed to interface with high-speed microprocessors with
minimum glue logic. Maximum access delay from clock rise is
7.5 ns (117-MHz version). A 2-bit on-chip counter captures the
first address in a burst and increments the address automati-
cally for the rest of the burst access. All synchronous inputs
are gated by registers controlled by a positive-edge-triggered
Clock Input (CLK). The synchronous inputs include all
addresses, all data inputs, address-pipelining Chip Enable
(CCoEn_{1tr)o, ldeinppthu-tesxp(AanDsSioCn,}
Chip Enables
ADSP, ^and
(CE₂
ADV),
aWndriCteE_{3E),naBbulresst}
(BW_[A:D], and
inputs include
BWE), ^{and Global}
the Output Enable
Write (GW).
(OE) _{and the}
Asynchronous
ZZ pin.
The CY7C1344F allows either interleaved or linear burst
sequences, selected by the MODE input pin. A HIGH selects
an interleaved burst sequence, while a LOW selects a linear
burst sequence. Burst accesses can be initiated with the
Processor Address Strobe (ADSP) or the cache Controller
Address Strobe (ADSC) inputs. Address advancement is
controlled by the Address Advancement (ADV) input.
Addresses and chip enables are registered at rising edge of
clock when either Address Strobe Processor (ADSP) or
Address Strobe Controller (ADSC) are active. Subsequent
burst addresses can be internally generated as controlled by
the Advance pin (ADV).
The CY7C1344F operates from a +3.3V core power supply
while all outputs may operate with a +3.3V supply. All inputs
and outputs are JEDEC-standard JESD8-5-compatible.
Logic Block Diagram
A0, A1, A
MODE
ADV
CLK
ADSC
ADSP
BWD
BWC
BWB
BWA
BWE
GW
CE1
CE2
CE3
OE
ZZ
ADDRESS
REGISTER
A[1:0]
BURST ^Q1
COUNTER
AND LOGIC
CLR
Q0
DQD, DQPD
BYTE
WRITE REGISTER
DQC, DQPC
BYTE
WRITE REGISTER
DQB, DQPB
BYTE
WRITE REGISTER
DQA, DQPA
BYTE
WRITE REGISTER
ENABLE
REGISTER
SLEEP
CONTROL
DQD, DQPD
BYTE
WRITE REGISTER
DQC, DQPC
BYTE
WRITE REGISTER
DQB, DQPB
BYTE
WRITE REGISTER
DQA, DQPA
BYTE
WRITE REGISTER
MEMORY
ARRAY
SENSE
AMPS
OUTPUT
BUFFERS
INPUT
REGISTERS
Note:
1. For best-practices recommendations, please refer to the Cypress application note System Design Guidelines on www.cypress.com.
DQs
DQPA
DQPB
DQPC
DQPD
Cypress Semiconductor Corporation • 3901 North First Street • San Jose, CA 95134 • 408-943-2600
Document #: 38-05432 Rev. *A
Revised April 9, 2004