|
CS4201 Datasheet, PDF (29/68 Pages) Cirrus Logic – CrystalClear Audio Codec 97 with headphone Amplifier | |||
|
◁ |
CS4201
4.12 Powerdown Control/Status Register (Index 26h)
D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0
EAPD PR6 PR5 PR4 PR3 PR2 PR1 PR0 0
0
0
0 REF ANL DAC ADC
EAPD
External Amplifier Power Down. The EAPD pin follows this bit and is generally used to power
down external amplifiers. The EAPD bit is mutually exclusive with the SDSC bit in the Serial
Port Control Register (Index 6Ah). The SDSC bit must be âclearâ before the EAPD bit may be
âsetâ. If the SDSC bit is âsetâ, EAPD is a read-only bit and always returns â0â.
PR6
Headphone Amplifier Powerdown. When âsetâ, the headphone amplifier is powered down.
PR5
Internal Clock Disable. When âsetâ, the internal master clock is disabled (BIT_CLK running).
The only way to recover from setting this bit is through a Cold Reset (driving the RESET# sig-
nal active).
PR4
AC-link Powerdown. When âsetâ, the AC-link is powered down (BIT_CLK off). The AC-link can
be restarted through a Warm Reset using the SYNC signal, or a Cold Reset using the RE-
SET# signal (primary audio codec only).
PR3
Analog Mixer Powerdown (Vref off). When âsetâ, the analog mixer and voltage reference are
powered down. When clearing this bit, the ANL, ADC, and DAC bits should be checked be-
fore writing any mixer registers.
PR2
Analog Mixer Powerdown (Vref on). When âsetâ, the analog mixer is powered down (the volt-
age reference is still active). When clearing this bit, the ANL bit should be checked before writ-
ing any mixer registers.
PR1
Front DACs Powerdown. When âsetâ, the DACs are powered down. When clearing this bit, the
DAC bit should be checked before sending any data to the DACs.
PR0
L/R ADCs and Input Mux Powerdown. When âsetâ, the ADCs and the ADC input muxes are
powered down. When clearing this bit, no valid data will be sent down the AC-link until the
ADC bit goes high.
REF
Voltage Reference Ready Status. When âsetâ, the REF bit indicates the voltage reference is
at a nominal level.
ANL
Analog Ready Status. When âsetâ, the analog output mixer, input multiplexer, and volume con-
trols are ready. When âclearâ, no volume control registers should be written.
DAC
Front DAC Ready Status. When âsetâ, the DACs are ready to receive data across the AC-link.
When âclearâ, the DACs will not accept any valid data.
ADC
L/R ADCs Ready Status. When âsetâ, the ADCs are ready to send data across the AC-link.
When âclearâ, no data will be sent to the controller.
Default
0000h. This value indicates all blocks are powered on. The lower four bits will change as the
CS4201 finishes an initialization and calibration sequence.
The PR[6:0] and the EAPD bits are powerdown control for different sections of the CS4201 as well as external am-
plifiers. The REF, ANL, DAC, and ADC bits are read-only status bits which, when âsetâ, indicate that a particular sec-
tion of the CS4201 is ready. After the controller receives the Codec Ready bit in input Slot 0, these status bits must
be checked before writing to any mixer registers. See Section 8, Power Management, for more information on the
powerdown functions.
DS483PP3
29
|
▷ |