CS4297 Datasheet, PDF (16/46 Pages) Cirrus Logic – CrystalClear SoundFusion Audio Codec 97

CS4297
CrystalClear™ SoundFusion™ Audio Codec ’97
Slot 0: Serial Data Output Slot Tags
The first slot, Slot 0, is a 16-bit slot which contains information about the validity of data for the remaining
12 slots. The 16 bits of this slot are defined as:
F0 F1 F2 F3 F4 F5 F6 F7 F8 F9 F10 F11 F12 F13 F14 F15
Bit 15 14 13 12 11 10
9
8
7
6
5
4
3
2
1
0
Valid Slot 1 Slot 2 Slot 3 Slot 4
Frame Valid Valid Valid Valid
Not Used
Valid Frame - Bit 15 determines if any of the following slots contain valid data. If this bit is ‘set’, at least
one of the other 12 slots contain valid data. If this bit is ‘cleared’, the remainder of the frame will be ig-
nored.
Slot 1 Valid - Bit 14 indicates the validity of data in the serial data output Slot 1. If this bit is ‘set’, Slot 1
contains valid data. If this bit is ‘cleared’, Slot 1 will be ignored.
Slot 2 Valid - Bit 13 indicates the validity of data in the serial data output Slot 2. If this bit is ‘set’, Slot 2
contains valid data. If this bit is ‘cleared’, Slot 2 will be ignored.
Slot 3 Valid - Bit 12 indicates the validity of data in the serial data output Slot 3. If this bit is ‘set’, Slot 3
contains valid data. If this bit is ‘cleared’, Slot 3 will be ignored.
Slot 4 Valid - Bit 11 indicates the validity of data in the serial data output Slot 4. If this bit is ‘set’, Slot 4
contains valid data. If this bit is ‘cleared’, Slot 4 will be ignored.
Slot 0 bits 10 through 0 represent unimplemented data slots in the CS4297 and will be ignored.
The input PCM data to the CS4297 on the SDATA_OUT pin is shifted out MSB justified (most significant
bit of the actual data of the 20-bit slots). In any case where there are less than 20-bits of valid data for a
slot (i.e.: 18-bit PCM data in a 20-bit slot), the trailing bits of the slot must be ‘cleared’ by the AC’97 Con-
troller. For Slots 5 - 12, the AC’97 Controller should ‘clear’ each bit in each frame, however data in these
slots will be ignored.
Slot 1: AC’97 Register Address
Slot 1 indicates the Register Address of the current frame’s register access. The 20 bits of this slot are de-
fined as:
F16 F17 F18 F19 F20 F21 F22 F23 F24 F25 F26 F27 F28 F29 F30 F31 F32 F33 F34 F35
Bit 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0
R/W RI6 RI5 RI4 RI3 RI2 RI1 RI0
Reserved
Table 1. Command Address Port Bit Definition
R/W - Bit 19 is the Read/Write bit. When this bit is ‘set’, a read of the AC’97 Register specified by the
Register Index will occur. When the bit is ‘cleared’, a write will occur. In both cases, register accesses only
occur when the Slot Valid bit 14 of Slot 0 (F1) corresponding to Slot 1 is ‘set’.
RI6 - RI0 - Bits 18-12 contain the 7-bit register index to the AC’97 Registers in the CS4297. All registers
are defined at word addressable boundaries. Bit 12 will be saved for historic purposes but is not decoded.
Bits 11-0 are reserved and should always be ‘cleared’ the AC’97 Controller.
16
DS242F5