UPG2158T5K_0512 Datasheet, PDF (3/11 Pages) California Eastern Labs – L, S-BAND SPDT SWITCH

µPG2158T5K
ELECTRICAL CHARACTERISTICS 1
(TA = +25°C, Vcont (H) = 2.7 V, Vcont (L) = 0 V, DC cut capacitors = 56 pF, unless otherwise specified)
Parameter
Insertion Loss 1
Insertion Loss 2
Insertion Loss 3
Insertion Loss 4
Isolation 1
Isolation 2
Isolation 3
Isolation 4
Input Return Loss
Output Return Loss
0.1 dB Loss Compression
Input Power ^{Note 2}
1 dB Loss Compression
Input Power ^{Note 3}
2nd Harmonics
3rd Harmonics
Input 3rd Order Distortion
Intercept Point
Switch Control Current
Switch Control Speed
Symbol
Test Conditions
LINS1 f = 0.05 to 1.0 GHz ^{Note 1}
LINS2 f = 1.0 to 2.0 GHz
LINS3 f = 2.0 to 2.5 GHz
LINS4
ISL1
f = 2.5 to 3.0 GHz
f = 0.05 to 1.0 GHz ^{Note 1}
ISL2 f = 1.0 to 2.0 GHz
ISL3 f = 2.0 to 2.5 GHz
ISL4
RLin
RLout
f = 2.5 to 3.0 GHz
f = 0.05 to 3.0 GHz ^{Note 1}
f = 0.05 to 3.0 GHz ^{Note 1}
Pin (0.1 dB) f = 2.0/2.5 GHz
f = 0.5 to 3.0 GHz
Pin (1 dB) f = 0.5 to 3.0 GHz
2f0 f = 2.0/2.5 GHz, Pin = +20 dBm
3f0 f = 2.0/2.5 GHz, Pin = +20 dBm
IIP3 f = 0.5 to 3.0 GHz
2 tone 5 MHz spacing
Icont No signal
tSW 50% CTL to 90/10% RF
MIN.
−
−
−
−
23
16
14
14
15
15
+26.0
−
−
TYP.
0.40
0.45
0.47
0.53
27
19
17
17
20
20
+29.0
+29.0
+30.5
MAX.
0.45
0.50
0.55
0.60
−
−
−
−
−
−
−
−
−
Unit
dB
dB
dB
dB
dBm
dBm
65
75
65
75
−
+60
−
dBc
−
dBc
−
dBm
−
0.2
20
µA
−
50
500
ns
Notes 1. DC cut capacitors = 1 000 pF at f = 0.05 to 0.5 GHz
2. Pin (0.1 dB) is measured the input power level when the insertion loss increases more 0.1 dB than that of
linear range.
3. Pin (1 dB) is measured the input power level when the insertion loss increases more 1 dB than that of linear
range.
Caution This device is used it is necessary to use DC cut capacitors.
The value of DC cut capacitors should be chosen to accommodate the frequency of operation,
bandwidth, switching speed and the condition with actual board of your system. The range of
recommended DC cut capacitor value is less than 100 pF.
Data Sheet PG10578EJ02V0DS
3