CAT25C08_06 Datasheet, PDF (2/16 Pages) Catalyst Semiconductor – 8K/16K SPI Serial CMOS EEPROM

CAT25C08/16
ABSOLUTE MAXIMUM RATINGS*
*COMMENT
Temperature Under Bias ................. –55°C to +125°C
Storage Temperature ....................... –65°C to +150°C
Voltage on any Pin with
Respect to VSS(1) .................. –1.5V to +VCC +1.5V
VCC with Respect to VSS ................................ –0.5V to +6.0V
Package Power Dissipation
Capability (Ta = 25°C) ................................... 1.0W
Lead Soldering Temperature (10 secs) ............ 300°C
Output Short Circuit Current⁽²⁾ ........................ 100 mA
Stresses above those listed under “Absolute Maximum
Ratings” may cause permanent damage to the device.
These are stress ratings only, and functional operation
of the device at these or any other conditions outside of
those listed in the operational sections of this specifica-
tion is not implied. Exposure to any absolute maximum
rating for extended periods may affect device perfor-
mance and reliability.
RELIABILITY CHARACTERISTICS
Symbol
Parameter
N_END(3)
T_DR(3)
VZAP(3)
ILTH(3)(4)
Endurance
Data Retention
ESD Susceptibility
Latch-up
Min.
1,000,000
100
2000
100
Typ.
Max.
Units
Cycles/Byte
Years
Volts
mA
D.C. OPERATING CHARACTERISTICS
V_CC = +1.8V to +5.5V, unless otherwise specified.
Limits
Symbol
Parameter
Min. Typ.
Max.
Units
Test Conditions
ICC1
Power Supply Current
(Operating Write)
5
mA VCC = 5V @ 5MHz
SO=open; CS=Vss
I_CC2
ISB(6)
I_LI
Power Supply Current
(Operating Read)
Power Supply Current
(Standby)
Input Leakage Current
3
mA V_CC = 5.5V
F_CLK = 5MHz
1
µA CS = VCC
V_IN = V_SS or V_CC
2
µA
I_LO
V_IL(5)
VIH(5)
Output Leakage Current
Input Low Voltage
Input High Voltage
-1
VCC x 0.7
3
V_CC x 0.3
VCC + 0.5
µA V_OUT = 0V to V_CC,
CS = 0V
V
V
V_OL1
V_OH1
Output Low Voltage
Output High Voltage
V_CC - 0.8
0.4
V
2.5V≤V_CC<5.5V
V
I_OL = 3.0mA
I_OH = -1.6mA
V_OL2
Output Low Voltage
0.2
V 1.8V≤V_CC<2.5V
VOH2
Output High Voltage
VCC-0.2
V
IOL = 150µA
IOH = -100µA
Note:
(1) The minimum DC input voltage is –0.5V. During transitions, inputs may undershoot to –1.5V for periods of less than 20 ns. Maximum DC
voltage on output pins is V_CC +0.5V, which may overshoot to V_CC +1.5V for periods of less than 20 ns.
(2) Output shorted for no more than one second. No more than one output shorted at a time.
(3) These parameter are tested initially and after a design or process change that affects the parameter according to appropriate AEC-Q100
and JEDEC test methods.
(4) Latch-up protection is provided for stresses up to 100 mA on address and data pins from –1V to V_CC +1V.
(5) V_ILMIN and V_IHMAX are reference values only and are not tested.
(6) Maximum standby current (I_SB ) = 10µA for the Automotive and Extended Automotive temperature range.
Doc. No. 1016, Rev. C
2
© 2006 by Catalyst Semiconductor, Inc.
Characteristics subject to change without notice