CAT24WC66 Datasheet, PDF (2/10 Pages) Catalyst Semiconductor – 64K-Bit I2C Serial CMOS EEPROM

CAT24WC66
ABSOLUTE MAXIMUM RATINGS*
Temperature Under Bias ................. –55°C to +125°C
Storage Temperature ....................... –65°C to +150°C
Voltage on Any Pin with
Respect to Ground⁽¹⁾ ........... –2.0V to +V_CC + 2.0V
V_CC with Respect to Ground ............... –2.0V to +7.0V
Package Power Dissipation
Capability (T_A = 25°C) ................................... 1.0W
Lead Soldering Temperature (10 secs) ............ 300°C
Output Short Circuit Current⁽²⁾ ........................ 100mA
*COMMENT
Stresses above those listed under “Absolute Maximum Ratings” may
cause permanent damage to the device. These are stress ratings only,
and functional operation of the device at these or any other conditions
outside of those listed in the operational sections of this specification is not
implied. Exposure to any absolute maximum rating for extended periods
may affect device performance and reliability.
RELIABILITY CHARACTERISTICS
Symbol Parameter
NEND⁽³⁾
Endurance
TDR⁽³⁾
Data Retention
VZAP⁽³⁾
ESD Susceptibility
ILTH⁽³⁾⁽⁴⁾
Latch-up
Reference Test Method
Min
Max
Units
MIL-STD-883, Test Method 1033 1,000,000
Cycles/Byte
MIL-STD-883, Test Method 1008
100
Years
MIL-STD-883, Test Method 3015
2000
Volts
JEDEC Standard 17
100
mA
D.C. OPERATING CHARACTERISTICS
V_CC = +1.8V to +6.0V, unless otherwise specified.
Symbol Parameter
Test Conditions
Min
Typ
Max
Units
I_CC
Power Supply Current
f_SCL = 100 kHz
I ⁽⁵⁾
SB
Standby Current (VCC = 5V) V_IN = GND or V_CC
I_LI
Input Leakage Current
V_IN = GND to V_CC
I
Output Leakage Current
LO
V = GND to V
OUT
CC
V_IL
Input Low Voltage
V_IH
Input High Voltage
V_OL1
Output Low Voltage
(V_CC = +3.0V)
V_OL2
Output Low Voltage
(V_CC = +1.8V)
I_OL = 3.0 mA
I_OL = 1.5 mA
CAPACITANCE T_A = 25°C, f = 1.0 MHz, V_CC = 5V
-1
V_CC x 0.7
3
mA
1
µA
10
µA
10
µA
V_CC x 0.3
V
V_CC + 0.5
V
0.4
V
0.5
V
Symbol Parameter
Conditions
Min
Typ
Max
Units
C (3)
I/O
Input/Output Capacitance
(SDA)
V_I/O = 0V
8
pF
C (3)
IN
Input Capacitance
(A0, A1, A2, SCL, WP)
V_IN = 0V
6
pF
Note:
(1) The minimum DC input voltage is –0.5V. During transitions, inputs may undershoot to –2.0V for periods of less than 20 ns. Maximum DC
voltage on output pins is V_CC +0.5V, which may overshoot to V_CC + 2.0V for periods of less than 20ns.
(2) Output shorted for no more than one second. No more than one output shorted at a time.
(3) This parameter is tested initially and after a design or process change that affects the parameter.
(4) Latch-up protection is provided for stresses up to 100 mA on address and data pins from –1V to V_CC +1V.
(5) Maximum standby current (I_SB ) = 10µA for the Automotive and Extended Automotive temperature range.
Doc. No. 1037, Rev. H
2