ADS7813 Datasheet, PDF (3/17 Pages) Burr-Brown (TI) – Low-Power, Serial 16-Bit Sampling ANALOG-TO-DIGITAL CONVERTER

SPECIFICATIONS (CONT)
At T_A = –40°C to +85°C, f_S = 40kHz, V_S = +5V ±5%, using internal reference, unless otherwise specified.
ADS7813P, U
PARAMETER
POWER SUPPLY
V_S
Power Dissipation
TEMPERATURE RANGE
Specified Performance
Derated Performance
CONDITIONS
f_S = 40kHz
MIN
+4.75
–40
–55
TYP
+5
MAX
+5.25
35
+85
+125
ADS7813PB, UB
MIN
TYP
MAX
T
T
T
T
T
T
T
T
UNITS
V
mW
°C
°C
T Same specification as grade to the left.
NOTES: (1) LSB means Least Significant Bit. For the ±10V input range, one LSB is 305µV. (2) Typical rms noise at worst case transitions and temperatures.
(3) Full scale error is the worst case of –Full Scale or +Full Scale untrimmed deviation from ideal first and last code transitions, divided by the transition voltage
(not divided by the full-scale range) and includes the effect of offset error. (4) After the ADS7813 is initially powered on and fully settles, this is the time delay
after it is brought out of Power Down Mode until all internal settling occurs and the analog input is acquired to rated accuracy, and normal conversions can begin
again. (5) All specifications in dB are referred to a full-scale input. (6) Useable Bandwidth defined as Full-Scale input frequency at which Signal-to-
(Noise+Distortion) degrades to 60dB, or 10 bits of accuracy. (7) Recovers to specified performance after 2 x FS input overvoltage.
ABSOLUTE MAXIMUM RATINGS
Analog Inputs: R1_IN ......................................................................... ±16.5V
R2_IN ..................................................................... GND – 0.3V to +16.5V
R3_IN ....................................................................................................... ±16.5V
REF ............................................ GND – 0.3V to V_S + 0.3V
CAP ............................................... Indefinite Short to GND
Momentary Short to V_S
V_S ........................................................................................................... 7V
Digital Inputs ...................................................... GND – 0.3V to V_S + 0.3V
Maximum Junction Temperature ................................................... +165°C
Internal Power Dissipation ............................................................. 825mW
Lead Temperature (soldering, 10s) ................................................ +300°C
ELECTROSTATIC
DISCHARGE SENSITIVITY
This integrated circuit can be damaged by ESD. Burr-Brown
recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling
and installation procedures can cause damage.
ESD damage can range from subtle performance degrada-
tion to complete device failure. Precision integrated circuits
may be more susceptible to damage because very small
parametric changes could cause the device not to meet its
published specifications.
PACKAGE/ORDERING INFORMATION
PRODUCT
MAXIMUM
INTEGRAL
LINEARITY
ERROR (LSB)
GUARANTEED
NO MISSING
CODE LEVEL
(LSB)
MINIMUM
SIGNAL-TO-
(NOISE + DISTORTION)
RATIO (dB)
SPECIFICATION
TEMPERATURE
RANGE
PACKAGE
ADS7813P
±3
15
ADS7813PB
±2
16
ADS7813U
±3
15
ADS7813UB
±2
16
85
–40°C to +85°C
Plastic DIP
87
–40°C to +85°C
Plastic DIP
85
–40°C to +85°C
SOIC
87
–40°C to +85°C
SOIC
NOTE: (1) For detailed drawing and dimension table, please see end of data sheet, or Appendix C of Burr-Brown IC Data Book.
PACKAGE
DRAWING
NUMBER⁽¹⁾
180
180
211
211
®
3
ADS7813