English
Language : 

AZ100EL16VS Datasheet, PDF (3/8 Pages) List of Unclassifed Manufacturers – ECL/PECL Differential Receiver with Variable Output Swing
◁
AZ100EL16VS
100K PECL DC Characteristics (VEE = GND, VCC = +5.0V)
Symbol
Characteristic
-40°C
0°C
25°C
85°C
Unit
Min Typ Max Min Typ Max Min Typ Max Min Typ Max
VOH
Output HIGH Voltage1,3 3915
VOL
Output LOW Voltage1,3
VCTRL = VBB2
3110
VOL
Output LOW Voltage1,3
VCTRL = VCC
3820
VIH
Input HIGH Voltage1
3835
VIL
Input LOW Voltage1
3190
VBB
Reference Voltage1
3580
4120
3380
3975
3130
4025
4120
3525
3740
3865
3835
3190
3580
4120
3320
3975
3130
4045
3225
4120
3320
3975
3130
4010
4120
3525
3740
3865
3835
3190
3580
3935
4010
4120
3525
3740
3865
3835
3190
3580
4120 mV
3320 mV
4010 mV
4120 mV
3525 mV
3740 mV
Input HIGH Current
IIH
D, D¯
150
150
150
150
μA
VCTRL
40
40
40
40
IIL
Input LOW Current
0.5
0.5
0.5
0.5
μA
IEE
Power Supply Current
18
25
18
25
18
25
21
26
mA
1. For supply voltages other that 5.0V, use the ECL table values and ADD supply voltage value.
2. If VCTRL is Open Circuit, use the VOH (Max & Min) and VOL (VCTRL = VREF : Max only) limits.
3. Each output is terminated through a 50Ω resistor to VCC – 2V.
AC Characteristics (VEE = -4.2V to -5.5V; VCC =GND or VEE =GND; VCC = +4.2V to +5.5V)
Symbol
Characteristic
-40°C
0°C
25°C
85°C
Unit
Min Typ Max Min Typ Max Min Typ Max Min Typ Max
Input to Output Delay
tPLH / tPHL
(Diff)
250
175 250 325 175 250 325 205 280 355
ps
(SE)
250
125 250 375 125 250 375 155 280 405
tSKEW
Duty Cycle Skew1 (Diff)
5
5
20
5
20
5
20
ps
VPP (AC) Minimum Input Swing2
150
150
150
150
mV
VCMR
Common Mode Range3
VCC -
2.0
VCC - VCC -
0.4 2.0
VCC - VCC -
0.4 2.0
VCC - VCC -
0.4 2.0
VCC -
0.4
V
tr / tf
Rise/Fall Time
20 – 80%
100
350 100
350 100
350 100
350
ps
1. Duty cycle skew is the difference between a tPLH and tPHL propagation delay through a device.
2. VPP is the minimum peak-to-peak differential input swing for which AC parameters are guaranteed.
3. The VCMR range is referenced to the most positive side of the differential input signal. Normal operation is obtained if the HIGH level falls within
the specified range and the peak-to-peak voltage lies between VPP(min) and 1V.
November 2006 * REV - 3
www.azmicrotek.com
3
 ▷