HFBR-0507Z Datasheet, PDF (7/12 Pages) AVAGO TECHNOLOGIES LIMITED – 125 Megabaud Versatile Link The Versatile Fiber Optic Connection

Electrical/Optical Characteristics 0 to 70°C, unless otherwise stated.
Parameter
Symbol Min. Typ.^[2]
Transmitter Output
Optical Power, 1 mm POF
P
-9.5 -7.0
T
-10.4
Transmitter Output
Optical Power, 1 mm POF
P
-6.0 -3.0
T
-6.9
Transmitter Output
Optical Power,
200 μm HCS^®
P
-14.6 -13.0
T
-15.5
Output Optical Power
Temperature Coefficient
ΔP
-0.02
T
ΔT
Peak Emission Wavelength
Peak Wavelength
Temperature Coefficient
_PK
640 650
Δ
0.12
ΔT
Spectral Width
FWHM
21
Max. Unit
-4.8 dBm
-4.3
-0.5 dBm
-0.0
-10.5 dBm
-10.0
dB/°C
660
nm
nm/°C
nm
Forward Voltage
Forward Voltage
Temperature Coefficient
Transmitter Numerical
Aperture
Thermal Resistance,
Junction to Case
Reverse Input Breakdown
Voltage
Diode Capacitance
Unpeaked Optical Rise
Time, 10% - 90%
Unpeaked Optical Fall
Time, 90% - 10%
V_F
1.8
2.1
2.4
V
ΔV
-1.8
mV/°C
F
ΔT
NA
0.5
_jc
140
V
3.0
13
BR
C
60
O
t
12
r
t_f
9
°C/W
V
pF
ns
ns
Condition
I = 20 mA, 25°C
F,dc
0-70°C
I = 60 mA, 25°C
F,dc
0-70°C
I = 60 mA, 25°C
F,dc
0-70°C
Note
Note 3
Note 3
Note 3
Full Width,
Half Maximum
I_F = 60 mA
I = -10 μA
F,dc
V = 0 V,
F
f = 1 MHz
I = 60 mA
F
f = 100 kHz
I_F = 60 mA
f = 100 kHz
Note 4
Figure 1
Note 5
Figure 1
Note 5
Notes:
1. 1.6 mm below seating plane.
2. Typical data is at 25°C.
3. Optical Power measured at the end of 0.5 meter of 1 mm diameter plastic or 200 μm diameter hard clad silica optical fiber with a large area
detector.
4. Typical value measured from junction to PC board solder joint for horizontal mount package, HFBR-1527Z. _jc is approximately
30°C/W higher for vertical mount package, HFBR-1537Z.
5. Optical rise and fall times can be reduced with the appropriate driver circuit; refer to Application Note 1066.
6. Pins 5 and 8 are primarily for mounting and retaining purposes, but are electrically connected; pins 3 and 4 are electrically unconnected. It is
recommended that pins 3, 4, 5, and 8 all be connected to ground to reduce coupling of electrical noise.
7. Refer to the Versatile Link Family Fiber Optic Cable and Connectors Technical Data Sheet for cable connector options for 1 mm plastic optical
fiber and 200 μm HCS fiber.
8. The LED current peaking necessary for high frequency circuit design contributes to electromagnetic interference (EMI). Care must be taken in
circuit board layout to minimize emissions for compliance with governmental EMI emissions regulations. Refer to Application Note 1066 for
design guidelines.
9. Moisture sensitivity level (MSL) is 3
7