HCPL-261A Datasheet, PDF (5/17 Pages) Agilent(Hewlett-Packard) – HCMOS Compatible, High CMR, 10 MBd Optocouplers

HCPL-061A/061N/063A/063N Outline Drawing
LAND PATTERN RECOMMENDATION
8765
3.937 ± 0.127
(0.155 ± 0.005)
XXX
YWW
1234
5.994 ± 0.203
(0.236 ± 0.008)
TYPE NUMBER
(LAST 3 DIGITS)
DATE CODE
0.406 ± 0.076
(0.016 ± 0.003)
1.270
(0.050)
BSC
7.49 (0.295)
1.9 (0.075)
0.64 (0.025)
* 5.080 ± 0.127
(0.200 ± 0.005)
7
45
X
0.432
(0.017)
3.175 ± 0.127
(0.125 ± 0.005)
1.524
(0.060)
0.228 ± 0.025
(0.009 ± 0.001)
* TOTAL PACKAGE LENGTH (INCLUSIVE OF MOLD FLASH)
5.207 ± 0.254 (0.205 ± 0.010)
DIMENSIONS IN MILLIMETERS (INCHES).
LEAD COPLANARITY = 0.10 mm (0.004 INCHES) MAX.
Figure 3. 8-Pin Small Outline Package Device Drawing.
0.203 ± 0.102
(0.008 ± 0.004)
0.305
(0.012)
MIN.
NOTE: FLOATING LEAD PROTRUSION IS 0.15 mm (6 mils) MAX.
Solder Reflow Thermal Profile
300
PREHEATING RATE 3°C + 1°C/–0.5°C/SEC.
REFLOW HEATING RATE 2.5°C ± 0.5°C/SEC. _PEAK
TEMP.
245°C
200
160°C
150°C
140°C
100
2.5 C ± 0.5°C/SEC.
3°C + 1°C/–0.5°C
PREHEATING TIME
150°C, 90 + 30 SEC.
30
SEC.
30
SEC.
PEAK
TEMP.
240°C
PEAK
TEMP.
230°C
SOLDERING
TIME
200°C
50 SEC.
ROOM
TEMPERATURE
00
TIGHT
TYPICAL
LOOSE
50
100
150
200
250
TIME (SECONDS)
Note: Non-halide flux should be used.
Recommended Pb-Free IR Profile
t_p
T_p
T_L
217 °C
260 +0/-5 °C
RAMP-UP
3 C/SEC. MAX.
T_smax ^{150 - 200 °C}
T_smin
t_s
PREHEAT
t_L
60 to 180 SEC.
TIME WITHIN 5 °C of ACTUAL
PEAK TEMPERATURE
20-40 SEC.
RAMP-DOWN
6 °C/SEC. MAX.
60 to 150 SEC.
25
t 25 °C to PEAK
TIME
NOTES:
THE TIME FROM 25 °C to PEAK TEMPERATURE = 8 MINUTES MAX.
T_smax = 200 °C, T_smin = 150 °C
Note: Non-halide flux should be used.

Regulatory Information
The HCPL-261A and HCPL-261N
families have been approved by the
following organizations:
UL
Recognized under UL 1577, Com-
ponent Recognition Program, File
E55361.
CSA
Approved under CSA Component
Acceptance Notice #5, File CA
88324.
IEC/EN/DIN EN 60747-5-2
Approved under:
IEC 60747-5-2:1997 + A1:2002
EN 60747-5-2:2001 + A1:2002
DIN EN 60747-5-2 (VDE 0884
Teil 2):2003-01.
(Option 060 only)