AJAV-5601 Datasheet, PDF (3/6 Pages) AVAGO TECHNOLOGIES LIMITED – W-CDMA/HSPA Band I Power Amplifier

Table 4. Electrical Specifications ^[1]
Parameter
Symbol Condition
Min Typ Max Unit
Frequency
Maximum Linear Output Power ^[2]
F_RF
P_MAX
HP mode
MP mode
1920 -
1980 MHz
+26.5 +27.0 -
dBm
+16.0 +16.5 -
dBm
Gain ^[2]
LP mode
G
HP mode
+5.5 +6.0 -
dBm
26.5 28.0 -
dB
MP mode
16.5 18.0 -
dB
RX Band Gain ^[2,3]
LP mode
G_RX
RX Band, 190 MHz offset
GPS Band, 1524 – 1577 MHz
6.0
8.0
-
dB
-
-15
-
dBc
-
-35
-
dBc
Adjacent Channel Leakage Ratio ^[2,4]
Noise ^[14]
ACLR1
ACLR2 ^[5]
N
ISM Band, 2400 – 2484 MHz
± 5 MHz offset
± 10 MHz offset
RX Band, 190 MHz offset
-
-34
-
dBc
-
-42
-38
dBc
-
-53
-48
dBc
-
-146 -
dBm/Hz
GPS Band, 1524 – 1577 MHz
-
-154 -
dBm/Hz
Error Vector Magnitude ^[2,4,5]
Power Added Efficiency ^[2,5,6]
ISM Band, 2400 – 2484 MHz
EVM
P_OUT ≤ P_MAX
PAE
HP mode
-
-156 -
dBm/Hz
-
1.5
3.35 %
-
40
-
%
MP mode
-
23
-
%
Quiescent Idle Current
Average Current ^[2,5,7]
Powerdown Current ^[4,8]
Logic Current ^[4,9]
Input Impedance ^[5]
Reverse Intermodulation^[4,5,10]
I_CQ
I_AVG
I_PD
I_CTRL
Z_IN
LP mode
Fixed battery
Average power tracking
VEN = V_IL
± 5 MHz offset
-
8
10
mA
-
25
-
mA
-
18
-
mA
-
5
10
mA
-
7
10
mA
-
1.4:1 2.5:1 VSWR
-
-
-31 dBc
Harmonics ^[2,4,5]
Instantaneous Phase Change ^[4,5,15]
Coupling Factor ^[11]
Daisy Chain Insertion Loss ^[5]
2F₀
3F₀, 4F₀
s34
± 10 MHz offset
Second harmonic
Third and fourth harmonic
Between power modes
UMTS Band II
-
-
-41 dBc
-
-
-35 dBc
-
-
-35 dBc
-
5
10
degree
-
-21
-
dB
-
-0.7 -
dB
Daisy Chain Return Loss ^[5,11]
UMTS Band V, VIII
s33, s44 UMTS Band II
-
-0.4 -
dB
-
-28
-
dB
UMTS Band V, VIII
-
-28
-
dB
Output Power Error ^[5,12]
Load VSWR = 2.5:1
-1
-
+1
dB
Turn-on Time ^[13]
T_ON
-
12
15
ms
Turn-off Time ^[5,13]
T_OFF
-
8
10
ms
Other Spurious ^[4,5]
Load VSWR ≤ 5:1
-
-
-70 dBc
Ruggedness ^[5]
No permanent damage or degradation -
-
10:1 VSWR
Notes:
1. Specifications at nominal operating conditions VIH = 1.8 V, VEN = 1.8 V, VBAT = 3.8 V, T_A = 25 °C, RF ports at 50 Ω, guaranteed over the full range of
operating frequency and guaranteed by production test unless indicated otherwise.
2. Specification is guaranteed using W-CDMA modulation RMC (12.2 kbps) in compliance with 3GPP Release 99.
3. RX band gain is specified relative to PA gain at 1950 MHz.
4. Specification is guaranteed over all power modes given in Table 3.
5. Specification is guaranteed by characterization.
6. Power added efficiency (PAE) includes total current consumption through all pins while PA is operating at maximum linear output power.
7. Calculated using three power modes (HP, MP, LP) with handset W-CDMA transmitter power distribution in GSMA DG.09 specification assuming 3
dB of post-PA loss.
8. Total supply current measured when the PA is disabled.
9. Specification applies to each VEN, VM0, and VM1 pin.
10. Interferer is CW at a relative power level of -40 dBc and offset from the W-CDMA modulated carrier.
11. Measured at CPLO pin.
12. Power variation measured at the RFO pin across 8 phase angles while power at CPLO pin is held constant.
13. Specified from the start of the PA enable transition to when the output power is within ±1 dB of final value.
14. Specification is guaranteed by characterization at P_MAX.
15. Phase change should be measured at the center channel at each switch point and compensated in the baseband.
3