HFBR-2521Z Datasheet, PDF (14/18 Pages) AVAGO TECHNOLOGIES LIMITED – Versatile Link The Versatile Fiber Optic Connection

HFBR-25X2Z/25X4Z Receivers
DO NOT CONNECT 5
DO NOT CONNECT 8
1000 
4 ^RL
3 ^VCC
2 ^GROUND
1 ^VO
Pin #
Function
1
V_O
2
Ground
3
V_CC
4
R_L
5
Do not connect
8
Do not connect


Note: Pins 5 and 8 are for mounting and retaining purposes only. Donot
electrically connect these pins.
Absolute Maximum Ratings
Parameter
Symbol
Min.
Max.
Units
Reference
Storage Temperature
T_S
–40
+85
°C
Operating Temperature
T_A
–40
+85
°C
Lead Soldering Cycle   
Temp.
260
°C
Note 1, 3
              Time
10
sec
Supply Voltage
V_CC
–0.5
7
V
Note 2
Output Collector Current
I_OAV 25
mA
Output Collector Power Dissipation
P_OD 40
mW
Output Voltage
V_O
–0.5
18
V
Pull-up Voltage
V_P
–5
V_CC
V
Fan Out (TTL)
N
5
Notes:
1. 1.6 mm below seating plane.
2. It is essential that a bypass capacitor 0.1 µF be connected from pin 2 to pin 3 of the receiver. Total lead length between both ends of the capacitor
and the pins should not exceed 20 mm.
3. Moisture sensitivity level (MSL) is 3.
Receiver Electrical/Optical Characteristics 0°C to 70°C, 4.75 V ≤V_CC ≤5.25 V unless otherwise specified.
Parameter
Symbol Min. Typ. Max. Units   Conditions
Ref.
Receiver   
HFBR-2522Z
P_R(L)
–24 dBm V_OL = 0 V
Optical Input I_OL = 8 mA
Power Level   HFBR-2524Z
–20
Notes 1, 2, 3
Note 4
Logic 0
Optical Input Power
P_R(H) -43 dBm V_OH = 5.25 V
Level Logic 1 I_OH = ≤250 µA
High Level Output Current
I_OH 5
250
µA V_O = 18 V, P_R = 0
Low Level Output Voltage
V_OL 0.4
0.5
V
I_OL = 8 mA
P_R = P_R(L)MIN
High Level Supply Current
I_CCH 3.5
6.3
mA V_CC = 5.25 V,
P_R = 0
Low Level Supply Current
I_CCL 6.2
10
mA V_CC = 5.25 V,
P_R = -12.5 dBm
Effective Diameter
D
1
mm
Note 5
Note 5
Note 5
Note 5
Numerical Aperture
NA
0.5
Internal Pull-up Resistor
R_L
680 1000 1700
Ω

Notes:
1. Measured at the end of the fiber optic cable with large area detector.
2. Pulsed LED operation at I_F > 80 mA will cause increased link t_PLH propagation delay time. This extended t_PLH time contributes to increased pulse
width distortion of the receiver output signal.
3. The LED drive circuit of Figure 11 is required for 1 MBd operation of the HFBR-25X2Z/25X4Z.
4. Optical flux, P (dBm) = 10 Log [P(µW)/1000 µW].
5. R_L is open.
14