HCNW136-300E Datasheet, PDF (12/16 Pages) AVAGO TECHNOLOGIES LIMITED – Single Channel, High Speed Optocouplers

Package Characteristics
Over recommended temperature (T_A = 0°C to 70°C) unless otherwise specified.
Parameter
Sym.
Device
Min. Typ.* Max. Units Test Conditions
Fig. Note
Input-Output
V_ISO
Momentary
8-Pin DIP
3750
V rms RH < 50%,
SO-8 t = 1 min.,
Withstand    Widebody     5000 T_A = 25°C
Voltage**
6, 14
6, 15

8-Pin DIP
5000 6, 12,
(Option 020) 15

I_I-O
8-Pin DIP
1
µA 45% RH, t = 5 s,
V_I-O = 3 kVdc,
T_A = 25°C
Input-Output
R_I-O
Resistance
8-Pin DIP
SO-8
10¹² Ω
V_I-O = 500 Vdc

Widebody
10¹² 10¹³ T_A = 25°C

10¹¹ T_A = 100°C
Input-Output
C_I-O
Capacitance
8-Pin DIP
SO-8
0.6
pF f = 1 MHz
6, 16
6
6
Widebody 0.5
0.6
*All typicals at T_A = 25°C.
**The Input-Output Momentary Withstand Voltage is a dielectric voltage rating that should not be interpreted as an input-output continuous
voltage rating. For the continuous voltage rating refer to the IEC/EN/DIN EN 60747-5-5 Insulation Related Characteristics Table (if applicable), your
equipment level safety specification or Avago Application Note 1074 entitled “Optocoupler Input-Output Endurance Voltage,” publication number
5963-2203E.
Notes:
  1.  Derate linearly above 70°C free-air temperature at a rate of 0.8 mA/°C (8-Pin DIP).
Derate linearly above 85°C free-air temperature at a rate of 0.5 mA/°C (SO-8).
  2.  Derate linearly above 70°C free-air temperature at a rate of 1.6 mA/°C (8-Pin DIP).
Derate linearly above 85°C free-air temperature at a rate of 1.0 mA/°C (SO-8).
  3.  Derate linearly above 70°C free-air temperature at a rate of 0.9 mW/°C (8-Pin DIP).
Derate linearly above 85°C free-air temperature at a rate of 1.1 mW/°C (SO-8).
  4.  Derate linearly above 70°C free-air temperature at a rate of 2.0 mW/°C (8-Pin DIP).
Derate linearly above 85°C free-air temperature at a rate of 2.3 mW/°C (SO-8).
  5.  CURRENT TRANSFER RATIO in percent is defined as the ratio of output collector current, I_O, to the forward LED input current, I_F, times 100.
  6.  Device considered a two-terminal device: Pins 1, 2, 3, and 4 shorted together and Pins 5, 6, 7, and 8 shorted together.
  7.  Common mode transient immunity in a Logic High level is the maximum tolerable (positive) dV_CM/dt on the leading edge of the common
mode pulse signal, V_CM, to assure that the output will remain in a Logic High state (i.e., V_O > 2.0 V). Common mode transient immunity in a
Logic Low level is the maximum tolerable (negative) dV_CM/dt on the trailing edge of the common mode pulse signal, V_CM, to assure that the
output will remain in a Logic Low state (i.e., V_O < 0.8 V).
  8.  The 1.9 kΩ load represents 1 TTL unit load of 1.6 mA and the 5.6 kΩ pull-up resistor.
  9.  The 4.1 kΩ load represents 1 LSTTL unit load of 0.36 mA and 6.1 kΩ pull-up resistor.
10.  The frequency at which the ac output voltage is 3 dB below its mid-frequency value.
11.  The JEDEC registration for the 6N136 specifies a minimum CTR of 15%. Avago guarantees a minimum CTR of 19%.
12.  See Option 020 data sheet for more information.
13.  Use of a 0.1 µf bypass capacitor connected between pins 5 and 8 is recommended.
14.  In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage ≥ 4500 V rms for 1 second (leakage
detection current limit, I_I-O ≤ 5 µA). This test is performed before the 100% Production test shown in the IEC/EN/DIN EN 60747-5-5 Insulation
Related Characteristics Table if applicable.
15.  In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage ≥ 6000 V rms for 1 second (leakage
detection current limit, I_I-O ≤ 5 µA). This test is performed before the 100% Production test shown in the IEC/EN/DIN EN 60747-5-5 Insulation
Related Characteristics Table if applicable.
16.  This rating is equally validated by an equivalent ac proof test.
12