10-69518-11S Datasheet, PDF (6/70 Pages) Amphenol Corporation – Amphenol QWL Series Cylindrical Connectors

QWL
how to order, cont.
ACCESSORIES
Cable Sealing Adapters - these are the basic connector accessories which provide moisture proofing and cable strain
relief. Selection is made on the basis of accessory style, shell size and cable dimensions. To illustrate the ordering proce-
dure, part number 10-101335-361 is shown as follows:
PART NUMBER
See code below:
10 - 101335 - 361
1
2
1. Accessory Base Number - refer to pages 41 through 52 for descriptions and dimensional data.10-101332 designates
short barrel length with woven strain relief grip
10-101333 designates short barrel length without strain relief
10-101334 designates short barrel length with woven strain relief grip and attaching ring for protection cap with bead
chain
10-101335 designates short barrel length with attaching ring for protection cap with bead chain
10-101380 designates short barrel length with attaching ring for protection cap with bead chain and clamp type strain
relief bars
10-113637 designates long barrel length with woven strain relief and attaching ring for protection cap with bead chain
2. Part Number – represents connector shell size and range of cable diameters accommodated by the sealing adapter.
Refer to the page listed below to determine the part number required for the accessory style being used:
Accessory Series
10-10133X
10-130380
10-113637
Page
46 - 48
44
50 - 52
Cable Clamp 10-749XX-( ) and Adapter 10-113196-XX
Connectors which require weatherproofing on open wire cables are provided with a moisture seal by this cable clamp, a
modification of the MS3057B design. A rubber grommet with holes for individual wires is used in place of the sleeve. As the
assembly is tightened, the grommet is compressed around each wire, sealing out moisture.
Order this clamp by the part number listed on page 53 to accommodate the connector being used. Suffix the part number
with the connector insert arrangement number.
To attach the cable clamp to the left hand accessory threads of QWL connectors, Adapter 10-113196-XX is needed. Finish
is non-conductive Alumilite. Order by adapter part number listed on page 53 to accommodate the connector shell size
being used. For a moisture proof seal, unused grommet holes must be filled with the appropriate size sealing plug or seal-
ing rod selected from the table on page 53. Sealing plug or sealing rods must be ordered separately.
M85049/1 Cable Clamp and Adapter 10-113138-XX - order this clamp by the M85049( )C part number listed on page 55
to accommodate the cable type being used. To attach the cable clamp to the left hand accessory threads of QWL connec-
tors, Adapter 10-113138-XX is needed. Order by adapter part number listed on page 55 to accommodate the connector
shell size being used. Standard finish on the clamp is olive drab, cadmium plate. Adapter finish is non-conductive Alumilite.
MS3420-( )A sleeve, to facilitate sealing on smaller diameter cables, must be ordered separately. MS3420-( )A sleeves
may be nested to accommodate smaller cable diameters.
Plug Protection Caps -
10-101046-( )
designates plug cover with chain, Alumilite 225 finish
10-101531-( )
designates plug cover with chain and eyelet end, Alumilite 225 finish
Order these plug covers by the part number listed on page 57 for the appropriate connector shell size.
Receptacle Protection Caps -
10-101063-( )
designates receptacle cover with chain, Alumilite 225 finish
10-101048-( )
designates receptacle cover with chain and eyelet, Alumilite 225 finish
Order these receptacle covers by the part number listed on page 57 for the appropriate connector shell size.
Flange Gasket -
10-36675-( )
10-40450-( )
for operating temperature range –67° to +275°F
for operating temperature range 0° to +257°F
Order by part number listed on page 59 for appropriate connector shell size.
10-183249 Grip Banding Clamp - order this stainless steel clamp by part number listed on page 59 to accommodate
cable diameter being used.
5