|
AMC2596 Datasheet, PDF (4/12 Pages) List of Unclassifed Manufacturers – 150 KHz, 3A STEP DOWN VOLTAGE REGULATOR | |||
|
◁ |
Temperature Range
Supply Voltage
RECOMMENDED OPERATING CONDITIONS
AMC2596
-40°Câ¦TJâ¦+125°C
4.5V to 40V
ELECTRICAL CHARACTERISTICS
Unless otherwise specified, these specifications apply VIN = 12V, ILOAD = 0.5A and the operating ambient temperatures TJ = 25°C.
Parameter
Symbol
Conditions
Min Typ Max Units
Output Voltage
Efficiency
Output Voltage
Efficiency
Feedback Voltage
Efficiency
VOUT
AMC2596-3.3
η
VOUT
AMC2596-5.0
η
VFB
AMC2596-ADJ
η
4.75V ⤠VIN ⤠40V, 0.2A ⤠ILOAD ⤠3A
VIN = 12V, ILOAD = 3A (Note 3)
7V ⤠VIN ⤠40V, 0.2A ⤠ILOAD ⤠3A
VIN = 12V, ILOAD = 3A (Note 3)
4.5V ⤠VIN ⤠40V, 0.2A ⤠ILOAD ⤠3A
VIN = 12V, ILOAD = 3A (Note 3)
3.168 3.3 3.342 V
73
%
4.800 5.0 5.200 V
80
%
1.193 1.230 1.267 V
73
%
Feedback Bias Current
Ib Adjustable Version Only, VFB =1.3V
10 50 nA
Oscillator Frequency
fOSC (Note 4)
127 150 173 KHz
Saturation Voltage
Max Duty Cycle (ON)
Min Duty Cycle (OFF)
Current Limit
VSAT IOUT = 3A (Note 5,6)
DC (Note 8,9)
ILIMIT Peak Current (Note 5,6)
1.16 1.4 V
100
%
0
3.6 4.5 6.9 A
Output Leakage Current
Output = 0V (Note 5,7)
ILEAK
Output = -1V (Note 8)
50 µA
2
30 mA
Quiescent Current
IQ (Note 9)
5 10 mA
Standby Current
ISTBY ENABLE pin=5V (OFF) (Note 8)
80 200 µA
ENABLE Pin Threshold Voltage
VIH Low(Regulator ON)
VIL High(Regulator OFF)
0.6 V
2.0
ENABLE Pin Input Current
IH VLOGIC=2.5V(Regulator OFF)
IL VLOGIC=0.5V(Regulator OFF)
5 15 µA
0.02 5 µA
Note 1ï¼Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which
the device is intended to be functional, but do not guarantee specific performance limits. For guaranteed specifications and test conditions,
see the Electrical Characteristics.
Note 2ï¼The human body model is a 100 pF capacitor discharged through a 1.5K resister into each pin.
Note 3ï¼External components such as the catch diode, inductor, input and output capacitors, and voltage programming resistors can affect switching
regulator system performance. When the AMC2596 is used as shown in the Figure 1 test circuit, system performance will be as shown in
system parameters section of Electrical Characteristics.
Note 4ï¼The switching frequency is reduced when the second stage current limit is activated. The amount of reduction is determined by the severity of
current over-load.
Note 5ï¼No diode, inductor or capacitor connected to output pin.
Note 6ï¼Feedback pin removed from output and connected to 0V to force the output transistor switch ON.
Note 7ï¼Feedback pin removed from output and connected to 12V for the 3.3V, 5V, and the ADJ. version, and 15Vfor the 12V version, to force the
output transistor switch OFF.
Note 8ï¼VINï¼40V
Copyright © 2006 ADDtek Corp.
4
DD008_A -- JUNE 2006
|
▷ |