UG-291 Datasheet, PDF (7/16 Pages) Analog Devices – The SDP-S board is designed to be used in conjunction

SDP-S User Guide
Pin No.
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
Pin Name
NC
NC
NC
EEPROM_A0
RESET_OUT
GND
DNU
RESET_IN
DNU
DNU
GND
NC
NC
NC
NC
NC
GND
NC
NC
DNU
DNU
GPIO7
GND
GPIO5
GPIO3
GPIO1
SCL_0
SDA_0
GND
SPI_CLK
SPI_MISO
SPI_MOSI
SPI_SEL_A
GND
DNU
DNU
DNU
DNU
DNU
DNU
GND
DNU
DNU
DNU
DNU
GND
DNU
DNU
DNU
DNU
DNU
GND
DNU
Description
No connect. Leave this pin unconnected. Do not ground.
No connect. Leave this pin unconnected. Do not ground.
No connect. Leave this pin unconnected. Do not ground.
EEPROM A0. Connect to the A0 address line of the EEPROM.
Active low pin for resetting the daughter board. Driven by SDP-S.
Connect to the ground plane of the daughter board.
Do not use. Leave this pin unconnected. Do not ground.
Active low pin to reset EVAL-SDP-CS1Z board.
Do not use. Leave this pin unconnected. Do not ground.
Do not use. Leave this pin unconnected. Do not ground.
Connect to the ground plane of the daughter board.
No connect. Leave this pin unconnected. Do not ground.
No connect. Leave this pin unconnected. Do not ground.
No connect. Leave this pin unconnected. Do not ground.
No connect. Leave this pin unconnected. Do not ground.
No connect. Leave this pin unconnected. Do not ground.
Connect to the ground plane of the daughter board.
No connect. Leave this pin unconnected. Do not ground.
No connect. Leave this pin unconnected. Do not ground.
Do not use. Leave this pin unconnected. Do not ground.
Do not use. Leave this pin unconnected. Do not ground.
General-purpose input/output.
Connect to the ground plane of the daughter board.
General-purpose input/output.
General-purpose input/output.
General-purpose input/output.
I²C Clock 0. The daughter board EEPROM must be connected to this bus.
I²C Data 0. The daughter board EEPROM must be connected to this bus.
Connect to the ground plane of the daughter board.
SPI clock.
SPI master in, slave out data.
SPI master out, slave in data.
SPI Chip Select A.
Connect to the ground plane of the daughter board.
Do not use. Leave this pin unconnected. Do not ground.
Do not use. Leave this pin unconnected. Do not ground.
Do not use. Leave this pin unconnected. Do not ground.
Do not use. Leave this pin unconnected. Do not ground.
Do not use. Leave this pin unconnected. Do not ground.
Do not use. Leave this pin unconnected. Do not ground.
Connect to the ground plane of the daughter board.
Do not use. Leave this pin unconnected. Do not ground.
Do not use. Leave this pin unconnected. Do not ground.
Do not use. Leave this pin unconnected. Do not ground.
Do not use. Leave this pin unconnected. Do not ground.
Connect to the ground plane of the daughter board.
Do not use. Leave this pin unconnected. Do not ground.
Do not use. Leave this pin unconnected. Do not ground.
Do not use. Leave this pin unconnected. Do not ground.
Do not use. Leave this pin unconnected. Do not ground.
Do not use. Leave this pin unconnected. Do not ground.
Connect to the ground plane of the daughter board.
Do not use. Leave this pin unconnected. Do not ground.
Rev. A | Page 7 of 16
UG-291