AD9389 Datasheet, PDF (30/48 Pages) Analog Devices – 800 MHz High Performance HDMI/DVI Transmitter

AD9389
Hex
Address
0x90
0x91
0x92
0x93
0x94
0x95
Read/Write or
Read Only
Read/Write
Read/Write
Read/Write
Read/Write
Read/Write
Read/Write
0x96
Read/Write
0x97
Read/Write
0x98
Read/Write
0x9C
0x9D
0xA2
0xA3
0xAF
Read/Write
Read/Write
Read/Write
Read/Write
Read/Write
0xB0
0xB1
0xB2
0xB3
0xB4
0xB5
0xB6
Read
Read
Read
Read
Read
Read
Read
Default
Bits Value
Register Name
[7:0] 00000000 ISRC2_ PB12
[7:0] 00000000 ISRC2_ PB13
[7:0] 00000000 ISRC2_ PB14
[7:0] 00000000 ISRC2_ PB15
[7:0] 11000000 mask1
[7:6] 00****** mask2
[7] 0******* HPD_INT
[6] *0****** MSEN_INT
[5] **0***** VS_INT
[4] ***0**** AUD_FIFO_FULL_INT
[3] ****0*** ITU656_ERR_INT
[2] *****0** EDID_RDY_INT
[7] 0******* HDCP_ERR_INT
[6] *0****** BKSV_flag
[2] *****0**
[7] 0******
[3:0] ****0010
[7:0]
[3:0] ****0***
[7:0]
[7:0]
[7] 0*******
Test bit
Test bits
Test bits
Test bit
Test bits
Test bits
HDCP_desired
[5] **0*****
[4] ***1**** frame_enc
[3] ****0***
[1] ******0* ext_HDMI_MODE
[0] *******0
[7:0] 00000000 An_0
[7:0] 00000000 An_1
[7:0] 00000000 An_2
[7:0] 00000000 An_3
[7:0] 00000000 An_4
[7:0] 00000000 An_5
[7:0] 00000000 An_6
Description
ISRC2 Packet Byte 12.
ISRC2 Packet Byte 13.
ISRC2 Packet Byte 14.
ISRC2 Packet Byte 15.
Mask for Interrupt Group1 (0x96).
Mask for Interrupt Group 2 (0x97[7:6].
[7] for HDCP error.
[6] for BKSV flag.
Interrupt for hot plug detect (HPD).
Interrupt for monitor connection (MSEN).
Interrupt for active VS edge.
Interrupt for audio FIFO overflow.
Interrupt for ITU656 error.
Interrupt for EDID Ready.
Interrupt bit from HDCP master.
Set to 1 to instruct the MPU to read the BKSV or the
EDID MEM for revocation list checking.
Must be written to 1 for proper operation.
Must be written to 0 for proper operation.
Must be written to 0x2 for proper operation.
Must be written to 0x3A for proper operation.
Must be written to 1 for proper operation.
Must be written to 0x87 for proper operation.
Must be written to 0x87 for proper operation.
HDCP encryption.
0 = input A/V content not to be encrypted.
1 = the input A/V content should be encrypted.
Default = 0.
Must be written to 0 for proper operation.
Frame encryption.
0 = the current frame should not be encrypted.
1 = the current frame should be encrypted.
Default = 1.
Must be written to 0 for proper operation.
HDMI mode.
0 = DVI.
1 = HDMI.
Default = 0.
Must be written to 0 for proper operation.
Byte 0 of An.
Byte 1 of An.
Byte 2 of An.
Byte 3 of An.
Byte 4 of An.
Byte 5 of An.
Byte 6 of An.
Rev. 0 | Page 30 of 48