OP450_15 Datasheet, PDF (3/5 Pages) Analog Devices – CMOS Single-Supply Rail-to-Rail Input/Output Operational Amplifier

OP150/OP250/OP450
ELECTRICAL CHARACTERISTICS ^{(@ V}S ^{= +5.0 V, V}CM ^{= 0.05 V, V}O ^{= 1.4 V, T}A ^{= +25؇C, unless otherwise noted)}
Parameter
Symbol
Conditions
Min
Typ
Max Units
INPUT CHARACTERISTICS
Offset Voltage OP150
V_OS
–40°C ≤ T_A ≤ +125°C
5
mV
mV
Offset Voltage OP250/OP450
V_OS
–40°C ≤ T_A ≤ +125°C
5
mV
mV
Input Bias Current
I_B
–40°C ≤ T_A ≤ +125°C
30
50 pA
60 pA
Input Offset Current
I_OS
0.1
8
pA
OBSOLETE ^{Input Voltage Range}
–40°C ≤ T_A ≤ +125°C
0
Common-Mode Rejection Ratio CMRR
V_CM = 0 V to 5 V
60
–40°C ≤ T_A ≤ +125°C
Large Signal Voltage Gain
A_VO
R_L = 10 kΩ, V_O = 0.3 V to 4.7 V
–40°C ≤ T_A ≤ +125°C
Large Signal Voltage Gain
A_VO
R_L = 2 kΩ, V_O = 0.3 V to 2.7 V
Large Signal Voltage Gain
A_VO
R_L = 1 kΩ, V_O = 0.3 V to 2.7 V
Offset Voltage Drift
∆V_OS/∆T
–40°C ≤ T_A ≤ +125°C
Bias Current Drift
∆I_B/∆T
Offset Current Drift
∆I_OS/∆T
OUTPUT CHARACTERISTICS
Output Voltage High
V_OH
Output Voltage Low
V_OL
I_L = 100 µA
–40°C to +125°C
I_L = 10 mA
–40°C to +125°C
I_L = 100 µA
16 pA
5
V
dB
dB
40
V/mV
V/mV
16
V/mV
10
V/mV
1.5
µV/°C
100
pA/°C
20
pA/°C
4.99
V
V
4.95
V
V
2
mV
–40°C to +125°C
mV
I_L = 10 mA
–40°C to +125°C
30
mV
mV
Output Current
I_OUT
–40°C to +125°C
± 250
mA
mA
Open Loop Impedance
Z_OUT
f = 1 MHz, A_V = 1
Ω
POWER SUPPLY
Power Supply Rejection Ratio
Supply Current/Amplifier
DYNAMIC PERFORMANCE
Slew Rate
Full Power Bandwidth
Settling Time
Gain Bandwidth Product
Phase Margin
Channel Separation
NOISE PERFORMANCE
Voltage Noise
Voltage Noise Density
Voltage Noise Density
Current Noise Density
PSRR
I_SY
SR
BW_p
t_S
GBP
Øo
CS
e_n p-p
e_n
e_n
i_n
V_S = 2.7 V to 6 V
–40°C ≤ T_A ≤ +125°C
V_O = 0 V
–40°C ≤ T_A ≤ +125°C
R_L =10 kΩ
1% Distortion
To 0.01%
f = 1 kHz, R_L =10 kΩ
0.1 Hz to 10 Hz
f = 1 kHz
f = 10 kHz
75
dB
70
dB
µA
550
650 µA
6.5
V/µs
kHz
µs
4
MHz
75
Degrees
dB
µV p-p
55
nV/√Hz
35
nV/√Hz
pA/√Hz
Specifications subject to change without notice.
This information applies to a product under development. Its characteristics and specifications are subject to change without notice.
Analog Devices assumes no obligation regarding future manufacture unless otherwise agreed to in writing.
REV. 0
–3–
PRELIMINARY TECHNICAL DATA