ADT7467 Datasheet, PDF (26/80 Pages) Analog Devices – dBCool Remote Thermal Monitor and Fan Controller

ADT7467
FAN DRIVE USING PWM CONTROL
The ADT7467 uses pulse-width modulation (PWM) to control
fan speed. This relies on varying the duty cycle (or on/off ratio)
of a square wave applied to the fan to vary the fan speed. The
external circuitry required to drive a fan using PWM control is
extremely simple. For 4-wire fans, the PWM drive might need
only a pull-up resistor. In many cases, the 4-wire fan PWM
input has a built-in pull-up resistor.
The ADT7467 PWM frequency can be set to a selection of low
frequencies or a single high PWM frequency. The low frequency
options are usually used for 2-wire and 3-wire fans, while the
high frequency option us usually used with 4-wire fans.
For 2-wire or 3-wire fans, a single N-channel MOSFET is the
only drive device required. The specifications of the MOSFET
depend on the maximum current required by the fan being
driven. Typical notebook fans draw a nominal 170 mA, and so
SOT devices can be used where board space is a concern. In
desktops, fans can typically draw 250 mA to 300 mA each. If
you drive several fans in parallel from a single PWM output or
drive larger server fans, the MOSFET must handle the higher
current requirements. The only other stipulation is that the
MOSFET should have a gate voltage drive, VGS < 3.3 V, for direct
interfacing to the PWM_OUT pin. VGS can be greater than 3.3
V as long as the pull-up on the gate is tied to 5 V. The MOSFET
should also have a low on resistance to ensure that there is not
significant voltage drop across the FET, which would reduce the
voltage applied across the fan and, therefore, the maximum
operating speed of the fan.
Figure 34 shows how to drive a 3-wire fan using PWM control.
12V 12V
TACH/AIN
ADT7467
PWM
10kΩ
10kΩ
4.7kΩ
3.3V
10kΩ
12V
FAN
1N4148
Q1
NDT3055L
Figure 34. Driving a 3-Wire Fan Using an N-Channel MOSFET
Figure 34 uses a 10 kΩ pull-up resistor for the TACH signal.
This assumes that the TACH signal is an open-collector from
the fan. In all cases, the TACH signal from the fan must be kept
below 5 V maximum to prevent damaging the ADT7467. If in
doubt as to whether the fan used has an open-collector or totem
pole TACH output, use one of the input signal conditioning
circuits shown in the Fan Speed Measurement section.
Figure 35 shows a fan drive circuit using an NPN transistor
such as a general-purpose MMBT2222. While these devices are
inexpensive, they tend to have much lower current handling
capabilities and higher on resistance than MOSFETs. When
choosing a transistor, care should be taken to ensure that it
meets the fan’s current requirements.
Ensure that the base resistor is chosen such that the transistor is
saturated when the fan is powered on.
Because 4-wire fans are powered continuously, the fan speed is
not switched on or off as with previous PWM driven/powered
fans. This enables it to perform better than 3-wire fans,
especially for high frequency applications. Figure 36 shows a
typical drive circuit for 4-wire fans.
TACH
ADT7467
PWM
12V 12V
10kΩ
10kΩ
4.7kΩ ^TACH
3.3V
12V
FAN
1N4148
665Ω
Q1
MMBT2222
Figure 35. Driving a 3-Wire Fan Using an NPN Transistor
TACH/AIN
ADT7467
PWM
12V 12V
10kΩ
10kΩ
TACH
4.7kΩ
3.3V
12V, 4-WIRE FAN
V_CC
TACH
PWM
2kΩ
Figure 36. Driving a 4-Wire Fan
Driving Two Fans from PWM3
The ADT7467 has four TACH inputs available for fan speed
measurement, but only three PWM drive outputs. If a fourth fan
is being used in the system, it should be driven from the PWM3
output in parallel with the third fan. Figure 37 shows how to
drive two fans in parallel using low cost NPN transistors.
Figure 38 shows the equivalent circuit using a MOSFET.
Rev. 0 | Page 26 of 80