OP400_07 Datasheet, PDF (14/16 Pages) Analog Devices – Quad Low Offset, Low Power Operational Amplifier

OP400
OUTLINE DIMENSIONS
0.005 (0.13) MIN 0.098 (2.49) MAX
14
8
PIN 1
1
7
0.100 (2.54) BSC
0.310 (7.87)
0.220 (5.59)
0.785 (19.94) MAX
0.060 (1.52)
0.200 (5.08)
MAX
0.200 (5.08)
0.125 (3.18)
0.023 (0.58)
0.014 (0.36)
0.015 (0.38)
0.150
(3.81)
MIN
0.070 (1.78)
SEATING
PLANE
0.030 (0.76)
0.320 (8.13)
0.290 (7.37)
0.015 (0.38)
15°
0.008 (0.20)
0°
CONTROLLING DIMENSIONS ARE IN INCHES; MILLIMETER DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF INCH EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN.
Figure 34. 14-Lead Ceramic Dual In-Line Package [CERDIP]
(Q-14)
[Y-Suffix]
Dimensions shown in inches and (millimeters)
0.775 (19.69)
0.750 (19.05)
0.735 (18.67)
14
8 _{0.280 (7.11)}
0.250 (6.35)
1
7 0.240 (6.10)
0.210 (5.33)
MAX
0.150 (3.81)
0.130 (3.30)
0.110 (2.79)
0.100 (2.54)
BSC
0.022 (0.56)
0.018 (0.46)
0.014 (0.36)
0.070 (1.78)
0.050 (1.27)
0.045 (1.14)
0.060 (1.52)
MAX
0.015
(0.38)
MIN
0.015 (0.38)
GAUGE
PLANE
SEATING
PLANE
0.005 (0.13)
MIN
0.325 (8.26)
0.310 (7.87)
0.300 (7.62)
0.195 (4.95)
0.130 (3.30)
0.115 (2.92)
0.430 (10.92)
MAX
0.014 (0.36)
0.010 (0.25)
0.008 (0.20)
COMPLIANT TO JEDEC STANDARDS MS-001
CONTROLLING DIMENSIONS ARE IN INCHES; MILLIMETER DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF INCH EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN.
CORNER LEADS MAY BE CONFIGURED AS WHOLE OR HALF LEADS.
Figure 35. 14-Lead Plastic Dual In-Line Package [PDIP]
(N-14)
[P-Suffix]
Dimensions shown in inches and (millimeters)
10.50 (0.4134)
10.10 (0.3976)
16
9
7.60 (0.2992)
7.40 (0.2913)
1
8
10.65 (0.4193)
10.00 (0.3937)
0.30 (0.0118)
0.10 (0.0039)
COPLANARITY
0.10
1.27 (0.0500)
BSC
0.51 (0.0201)
0.31 (0.0122)
2.65 (0.1043)
2.35 (0.0925)
8°
0°
SEATING
PLANE
0.33 (0.0130)
0.20 (0.0079)
0.50 (0.0197) _45°
0.25 (0.0098)
1.27 (0.0500)
0.40 (0.0157)
COMPLIANT TO JEDEC STANDARDS MS-013- AA
CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN.
Figure 36. 16-Lead Standard Small Outline Package [SOIC_W]
Wide Body (R-16)
[S-Suffix]
Dimensions shown in millimeters and (inches)
Rev. E | Page 14 of 16