ADSP-21060LCW-133 Datasheet, PDF (10/48 Pages) Analog Devices – ADSP-21060 Industrial SHARC DSP Microcomputer Family

ADSP-21060C/ADSP-21060LC
Pin
TFSx
RFSx
LxDAT_3-0
LxCLK
LxACK
EBOOT
LBOOT
BMS
CLKIN
RESET
TCK
TMS
TDI
TDO
TRST
EMU (O/D)
ICSA
VDD
GND
NC
Type
I/O
I/O
I/O
I/O
I/O
I
I
I/O/T*
I
I/A
I
I/S
I/S
O
I/A
O
O
P
G
Function
Transmit Frame Sync (Serial Ports 0, 1).
Receive Frame Sync (Serial Ports 0, 1).
Link Port Data (Link Ports 0–5). Each LxCLK pin has a 50 kΩ internal pull-down resistor that is
enabled or disabled by the LPDRD bit of the LCOM register.
Link Port Clock (Link Ports 0–5). Each LxCLK pin has a 50 kΩ internal pull-down resistor that is
enabled or disabled by the LPDRD bit of the LCOM register.
Link Port Acknowledge (Link Ports 0–5). Each LxACK pin has a 50 kΩ internal pull-down resistor
that is enabled or disabled by the LPDRD bit of the LCOM register.
EPROM Boot Select. When EBOOT is high, the ADSP-2106x is configured for booting from an 8-
bit EPROM. When EBOOT is low, the LBOOT and BMS inputs determine booting mode. See table
below. This signal is a system configuration selection that should be hardwired.
Link Boot. When LBOOT is high, the ADSP-2106x is configured for link port booting. When
LBOOT is low, the ADSP-2106x is configured for host processor booting or no booting. See table
below. This signal is a system configuration selection that should be hardwired.
Boot Memory Select. Output: Used as chip select for boot EPROM devices (when EBOOT = 1,
LBOOT = 0). In a multiprocessor system, BMS is output by the bus master. Input: When low, indi-
cates that no booting will occur and that ADSP-2106x will begin executing instructions from external
memory. See table below. This input is a system configuration selection that should be hardwired.
*Three-statable only in EPROM boot mode (when BMS is an output).
EBOOT
LBOOT
BMS
Booting Mode
1
0
Output
EPROM (Connect BMS to EPROM chip select.)
0
0
1 (Input)
Host Processor
0
1
1 (Input)
Link Port
0
0
0 (Input)
No Booting. Processor executes from external memory.
0
1
0 (Input)
Reserved
1
1
x (Input)
Reserved
Clock In. External clock input to the ADSP-2106x. The instruction cycle rate is equal to CLKIN.
CLKIN may not be halted, changed, or operated below the minimum specified frequency.
Processor Reset. Resets the ADSP-2106x to a known state and begins execution at the program
memory location specified by the hardware reset vector address. This input must be asserted (low) at
power-up.
Test Clock (JTAG). Provides an asynchronous clock for JTAG boundary scan.
Test Mode Select (JTAG). Used to control the test state machine. TMS has a 20 kΩ internal pull-up
resistor.
Test Data Input (JTAG). Provides serial data for the boundary scan logic. TDI has a 20 kΩ internal
pull-up resistor.
Test Data Output (JTAG). Serial scan output of the boundary scan path.
Test Reset (JTAG). Resets the test state machine. TRST must be asserted (pulsed low) after power-
up or held low for proper operation of the ADSP-2106x. TRST has a 20 kΩ internal pull-up resistor.
Emulation Status. Must be connected to the ADSP-2106x EZ-ICE target board connector only.
Reserved, leave unconnected.
Power Supply; nominally 5.0 V dc for 5 V devices or 3.3 V dc for 3.3 V devices. (30 pins).
Power Supply Return. (30 pins).
Do Not Connect. Reserved pins which must be left open and unconnected.
–10–
REV. B