AD9523BCPZ Datasheet, PDF (1/60 Pages) Analog Devices – Jitter Cleaner and Clock Generator with 14 Differential or 29 LVCMOS Outputs

Data Sheet
Jitter Cleaner and Clock Generator with
14 Differential or 29 LVCMOS Outputs
AD9523
FEATURES
Output frequency: <1 MHz to 1 GHz
Start-up frequency accuracy: <±100 ppm (determined by
VCXO reference accuracy)
Zero delay operation
Input-to-output edge timing: <150 ps
14 outputs: configurable LVPECL, LVDS, HSTL, and LVCMOS
14 dedicated output dividers with jitter-free adjustable delay
Adjustable delay: 63 resolution steps of ½ period of VCO
output divider
Output-to-output skew: <50 ps
Duty-cycle correction for odd divider settings
Automatic synchronization of all outputs on power-up
Absolute output jitter: <200 fs at 122.88 MHz
Integration range: 12 kHz to 20 MHz
Distribution phase noise floor: −160 dBc/Hz
Digital lock detect
Nonvolatile EEPROM stores configuration settings
SPI- and I²C-compatible serial control port
Dual PLL architecture
PLL1
Low bandwidth for reference input clock cleanup with
external VCXO
Phase detector rate of 300 kHz to 75 MHz
Redundant reference inputs
Auto and manual reference switchover modes
Revertive and nonrevertive switching
Loss of reference detection with holdover mode
Low noise LVCMOS output from VCXO used for RF/IF
synthesizers
PLL2
Phase detector rate of up to 250 MHz
Integrated low noise VCO
APPLICATIONS
LTE and multicarrier GSM base stations
Wireless and broadband infrastructure
Medical instrumentation
Clocking high speed ADCs, DACs, DDSs, DDCs, DUCs, MxFEs
Low jitter, low phase noise clock distribution
Clock generation and translation for SONET, 10Ge, 10G FC,
and other 10 Gbps protocols
Forward error correction (G.710)
High performance wireless transceivers
ATE and high performance instrumentation
FUNCTIONAL BLOCK DIAGRAM
REFA,
REFA
REFB,
REFB
REF_TEST
OSC_IN, OSC_IN
PLL1
PLL2
AD9523
OUT0,
OUT0
OUT1,
OUT1
SCLK/SCL
SDIO/SDA
SDO
CONTROL
INTERFACE
(SPI AND I²C)
ZERO
DELAY
EEPROM
14-CLOCK
DISTRIBUTION
OUT12,
OUT12
OUT13,
OUT13
ZD_IN, ZD_IN
Figure 1.
GENERAL DESCRIPTION
The AD9523 provides a low power, multi-output, clock distribution
function with low jitter performance, along with an on-chip PLL
and VCO. The on-chip VCO tunes from 3.6 GHz to 4.0 GHz.
The AD9523 is defined to support the clock requirements for
long term evolution (LTE) and multicarrier GSM base station
designs. It relies on an external VCXO to provide the reference
jitter cleanup to achieve the restrictive low phase noise require-
ments necessary for acceptable data converter SNR performance.
The input receivers, oscillator, and zero delay receiver provide
both single-ended and differential operation. When connected
to a recovered system reference clock and a VCXO, the device
generates 14 low noise outputs with a range of 1 MHz to 1 GHz,
and one dedicated buffered output from the input PLL (PLL1).
The frequency and phase of one clock output relative to another
clock output can be varied by means of a divider phase select
function that serves as a jitter-free coarse timing adjustment in
increments that are equal to half the period of the signal
coming out of the VCO.
An in-package EEPROM can be programmed through the serial
interface to store user-defined register settings for power-up
and chip reset.
Rev. C
Document Feedback
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: [phone] ©2010–2013 Analog Devices, Inc. All rights reserved.
Technical Support
www.analog.com