AD7918_15 Datasheet, PDF (1/28 Pages) Analog Devices – 8-Channel, 1 MSPS, 8-/10-/12-Bit ADCs with Sequencer in 20-Lead TSSOP

Data Sheet
8-Channel, 1 MSPS, 8-/10-/12-Bit ADCs
with Sequencer in 20-Lead TSSOP
AD7908/AD7918/AD7928
FEATURES
Fast throughput rate: 1 MSPS
Specified for AVDD of 2.7 V to 5.25 V
Low power
6.0 mW max at 1 MSPS with 3 V supply
13.5 mW max at 1 MSPS with 5 V supply
Eight (single-ended) inputs with sequencer
Wide input bandwidth
AD7928, 70 dB min SINAD at 50 kHz input frequency
Flexible power/serial clock speed management
No pipeline delays
High speed serial interface SPI®/QSPI™/
MICROWIRE™/DSP compatible
Shutdown mode: 0.5 μA max
20-lead TSSOP package
Qualified for automotive applications
GENERAL DESCRIPTION
The AD7908/AD7918/AD7928 are, respectively, 8-bit, 10-bit, and
12-bit, high speed, low power, 8-channel, successive approximation
ADCs. The parts operate from a single 2.7 V to 5.25 V power
supply and feature throughput rates up to 1 MSPS. The parts
contain a low noise, wide bandwidth track-and-hold amplifier that
can handle input frequencies in excess of 8 MHz.
The conversion process and data acquisition are controlled using
CS and the serial clock signal, allowing the device to easily interface
with microprocessors or DSPs. The input signal is sampled on the
falling edge of CS and conversion is also initiated at this point.
There are no pipeline delays associated with the part.
The AD7908/AD7918/AD7928 use advanced design techniques to
achieve very low power dissipation at maximum throughput rates.
At maximum throughput rates, the AD7908/AD7918/AD7928
consume 2 mA maximum with 3 V supplies; with 5 V supplies, the
current consumption is 2.7 mA maximum.
Through the configuration of the control register, the analog input
range for the part can be selected as 0 V to REFIN or 0 V to 2 ×
REFIN, with either straight binary or twos complement output
coding. The AD7908/AD7918/AD7928 each feature eight single-
ended analog inputs with a channel sequencer to allow a
preprogrammed selection of channels to be converted sequentially.
The conversion time for the AD7908/AD7918/AD7928 is
determined by the SCLK frequency, which is also used as the
master clock to control the conversion.
Rev. E
Document Feedback
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
FUNCTIONAL BLOCK DIAGRAM
AV_DD
REF_IN
V_IN0
•
•
•
•
•
•
•
•
•
•
•
•
•
V_IN7
T/H
I/P
MUX
8-/10-/12-BIT
SUCCESSIVE
APPROXIMATION
ADC
SEQUENCER
CONTROL LOGIC
AD7908/AD7918/AD7928
GND
Figure 1.
PRODUCT HIGHLIGHTS
SCLK
DOUT
DIN
CS
V_DRIVE
1. High Throughput with Low Power Consumption. The AD7908/
AD7918/AD7928 offer up to 1 MSPS throughput rates. At the
maximum throughput rate with 3 V supplies, the AD7908/
AD7918/AD7928 dissipate just 6 mW of power maximum.
2. Eight Single-Ended Inputs with a Channel Sequencer.
A sequence of channels can be selected, through which
the ADC cycles and converts on.
3. Single-Supply Operation with VDRIVE Function. The AD7908/
AD7918/AD7928 operate from a single 2.7 V to 5.25 V supply.
The VDRIVE function allows the serial interface to connect directly
to either 3 V or 5 V processor systems independent of AVDD.
4. Flexible Power/Serial Clock Speed Management. The conversion
rate is determined by the serial clock, allowing the conversion
time to be reduced through the serial clock speed increase. The
parts also feature various shutdown modes to maximize power
efficiency at lower throughput rates. Current consumption is
0.5 μA max when in full shutdown.
5. No Pipeline Delay. The parts feature a standard successive
approximation ADC with accurate control of the sampling
instant via a CS input and once off conversion control.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: [phone] ©2006–2014 Analog Devices, Inc. All rights reserved.
Technical Support
www.analog.com