LPS6225 Datasheet, PDF (1/2 Pages) Coilcraft lnc. – Shielded Power Inductors

Document 554-1
Shielded Power Inductors – LPS6225
• Low DCR; high current; shielded construction
• Perfect for backlight applications
Designer’s Kit C349 contains 3 each of all values
Core material Ferrite
Core and winding loss See www.coilcraft.com/coreloss
Environmental  RoHS compliant, halogen free
Terminations  RoHS compliant matte tin over nickel over silver.
Other terminations available at additional cost.
Weight  309 – 331 mg
Ambient temperature  –40°C to +85°C with (40°C rise) Irms current.
Maximum part temperature  +125°C (ambient + temp rise). Derating.
Storage temperature  Component: –40°C to +125°C.
Tape and reel packaging: –40°C to +80°C
Resistance to soldering heat  Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Moisture Sensitivity Level (MSL)  1 (unlimited floor life at <30°C /
85% relative humidity)
Failures in Time (FIT) / Mean Time Between Failures (MTBF)
38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332
Packaging  750/7″ reel; 2500/13″ reel  Plastic tape:  12 mm wide,
0.3 mm thick, 8 mm pocket spacing, 2.57 mm pocket depth
Recommended pick and place nozzle  OD: 6.2 mm;  ID: ≤ 3.1 mm
PCB washing  Tested to MIL-STD-202 Method 215 plus an additional
aqueous wash. See Doc787_PCB_Washing.pdf.

DCR SRF
  _{Isat (A)}5 _{    Irms (A)}6
^  Inductance^{2  } max^{3  } typ⁴ 10% 20% 30% 20°C 40°C
  _{Part number}1 _{± 20% (µH) (Ohms) (MHz) drop drop drop rise rise}
LPS6225-122MR_
LPS6225-222MR_
LPS6225-332MR_
LPS6225-472MR_
LPS6225-682MR_
1.2 0.040 178 5.3 5.4 5.4 1.1 1.65
2.2 0.045 100 3.9 4.0 4.1 1.0 1.40
3.3 0.055 68 3.5 3.5 3.6 1.0 1.35
4.7 0.065 53 3.0 3.1 3.2 0.90 1.30
6.8 0.095 40 2.6 2.7 2.8 0.90 1.30
LPS6225-103MR_ 10
LPS6225-153MR_ 15
LPS6225-223MR_ 22
LPS6225-333MR_ 33
LPS6225-473MR_ 47
0.105 35 2.1 2.1 2.2 0.90 1.30
0.135 23 2.1 2.2 2.2 0.85 1.20
0.175 17 1.4 1.5 1.6 0.80 1.10
0.260 14 1.1 1.2 1.2 0.65 0.90
0.360 10 0.98 1.0 1.0 0.60 0.80
LPS6225-683MR_ 68
LPS6225-104MR_ 100
LPS6225-124MR_ 120
LPS6225-154MR_ 150
LPS6225-224MR_ 220
0.420
0.610
0.750
0.920
1.30
9.6 0.58 0.61 0.62 0.57 0.74
7.7 0.48 0.51 0.52 0.47 0.64
7.4 0.42 0.45 0.46 0.43 0.58
6.4 0.39 0.41 0.42 0.40 0.54
5.0 0.32 0.34 0.35 0.37 0.50
LPS6225-334MR_
LPS6225-474MR_
LPS6225-684MR_
LPS6225-105MR_
LPS6225-155MR_
330
470
680
1000
1500
2.00 3.8 0.26 0.27 0.28 0.28 0.39
2.60 3.2 0.22 0.23 0.24 0.24 0.37
4.00 2.8 0.18 0.19 0.20 0.18 0.26
6.00 2.3 0.15 0.16 0.17 0.15 0.24
9.00 1.8 0.12 0.13 0.13 0.13 0.20
LPS6225-185MR_ 1800
11.7
LPS6225-225MR_ 2200
13.5
LPS6225-335MR_ 3300
21.0
LPS6225-475MR_ 4700
30.0
LPS6225-565MR_ 5600
36.0
1.7 0.11
1.3 0.10
1.1 0.099
0.90 0.086
0.72 0.083
0.12
0.10
0.10
0.096
0.090
0.12
0.11
0.11
0.10
0.096
0.11 0.14
0.11 0.13
0.080 0.11
0.075 0.090
0.070 0.090
LPS6225-685MR_ 6800
43.0
LPS6225-825MR_ 8200
54.0
LPS6225-106MR_ 10000
70.0
0.70 0.080 0.086 0.089 0.065 0.080
0.69 0.079 0.086 0.088 0.060 0.075
0.68 0.075 0.084 0.087 0.060 0.065
1. Please specify termination and packaging codes:
LPS6225-106MRC
Termination: R = RoHS compliant matte tin over
nickel over silver.
Special order, added cost:
Q = RoHS tin-silver-copper (95.5/4/0.5)
or P = non-RoHS tin-lead (63/37).
Packaging: C = 7″ machine-ready reel. EIA-481
embossed plastic tape (750 parts
per full reel).
B = Less than full reel. In tape, but not
machine ready. To have a leader and
trailer added ($25 charge), use code
letter C instead.
D = 13″ machine-ready reel. EIA-481
embossed plastic tape. Factory
order only, not stocked (2500 parts
per full reel).
2. Inductance tested at 100 kHz, 0.1 Vrms, 0 Adc.
3. DCR measured on a micro-ohmmeter.
4. SRF measured using Agilent/HP 8753ES or equivalent.
5. DC current at 25°C that causes the specified induc-
tance drop from its value without current.
Click for temperature derating information.
6. Current that causes the specified temperature rise from
25°C ambient. This information is for reference only and
does not represent absolute maximum ratings.
Click for temperature derating information.
7. Electrical specifications at 25°C.
Refer to Doc 362 “Soldering Surface Mount Components”
before soldering.
Document 554-1  Revised 09/02/15