LPS5010 Datasheet, PDF (1/2 Pages) Coilcraft lnc. – Shielded Power Inductors

Document 536-1
Shielded Power Inductors – LPS5010
• Very low DCR; excellent current handling
• 5.0 × 5.0 mm footprint; less than 1.0 mm tall
Designer’s Kit C407 contains 3 each of all values
Core material Ferrite
Core and winding loss See www.coilcraft.com/coreloss
Environmental  RoHS compliant, halogen free
Terminations  RoHS compliant matte tin over nickel over silver.
Other terminations available at additional cost.
Weight  70 – 75 mg
Ambient temperature  –40°C to +85°C with (40°C rise) Irms current.
Maximum part temperature  +125°C (ambient + temp rise). Derating.
Storage temperature  Component: –40°C to +125°C.
Tape and reel packaging: –40°C to +80°C
Resistance to soldering heat  Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Moisture Sensitivity Level (MSL)  1 (unlimited floor life at <30°C /
85% relative humidity)
Failures in Time (FIT) / Mean Time Between Failures (MTBF)
38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332
Packaging  1000/7″ reel; 3000/13″ reel  Plastic tape:  12 mm wide,
0.3 mm thick, 8 mm pocket spacing, 1.02 mm pocket depth
Recommended pick and place nozzle  OD: 5 mm;  ID: ≤ 2.5 mm
PCB washing  Tested to MIL-STD-202 Method 215 plus an additional
aqueous wash. See Doc787_PCB_Washing.pdf.

DCR SRF
  _{Isat (A)}5 _{    Irms (A)}6
^  Inductance^{2  } max^{3  } typ⁴ 10% 20% 30% 20°C 40°C
  _{Part number}1 _{±20% (µH) (Ohms) (MHz) drop drop drop rise rise}
LPS5010-471MR_ 0.47 0.038 290 3.1 3.3 3.4 2.0 2.7
LPS5010-821MR_ 0.82 0.058 195 2.3 2.5 2.6 1.2 1.5
LPS5010-152MR_ 1.5
0.072 168 1.7 1.8 1.9 0.90 1.4
LPS5010-222MR_ 2.2
0.100 144 1.4 1.5 1.6 0.88 1.2
LPS5010-332MR_ 3.3
0.125 105 1.1 1.2 1.3 0.86 1.1
LPS5010-472MR_ 4.7
LPS5010-562MR_ 5.6
LPS5010-682MR_ 6.8
LPS5010-103MR_ 10
LPS5010-153MR_ 15
0.175
0.240
0.255
0.350
0.500
76 0.95 1.1 1.1 0.85 0.98
75 0.90 0.97 1.00 0.75 0.92
71 0.82 0.90 0.93 0.74 0.85
51 0.66 0.72 0.74 0.73 0.80
39 0.55 0.59 0.62 0.68 0.75
LPS5010-223MR_ 22
LPS5010-333MR_ 33
LPS5010-473MR_ 47
LPS5010-683MR_ 68
LPS5010-104MR_ 100
0.670
1.05
1.45
2.00
3.10
32 0.47 0.51 0.53 0.46 0.62
26 0.38 0.42 0.43 0.40 0.55
20 0.31 0.34 0.36 0.33 0.44
15 0.26 0.29 0.30 0.25 0.35
12 0.21 0.23 0.24 0.21 0.28
LPS5010-124MR_ 120
LPS5010-154MR_ 150
LPS5010-224MR_ 220
LPS5010-334MR_ 330
LPS5010-474MR_ 470
3.50
4.25
6.25
8.60
12.7
11 0.20 0.22 0.23 0.19 0.25
9.0 0.18 0.20 0.21 0.17 0.23
7.0 0.15 0.16 0.17 0.15 0.20
5.5 0.12 0.13 0.14 0.13 0.185
4.5 0.090 0.11 0.11 0.11 0.150
LPS5010-564MR_ 560
15.7
LPS5010-684MR_ 680
20.0
4.0 0.090 0.10 0.10 0.10 0.135
3.7 0.090 0.097 0.10 0.090 0.125
1. Please specify termination and packaging codes:
LPS5010-684MRC
Termination: R= RoHS compliant matte tin over
nickel over silver.
Special order, added cost:
Q = RoHS tin-silver-copper (95.5/4/0.5)
or P = non-RoHS tin-lead (63/37).
Packaging: C= 7″ machine-ready reel. EIA-481
embossed plastic tape (1000 parts
per full reel).
B= Less than full reel. In tape, but not
machine ready.
To have a leader and trailer added
($25 charge), use code letter C
instead.
D= 13″ machine-ready reel. EIA-481
embossed plastic tape. Factory
order only, not stocked (3500 parts
per full reel).
2. Inductance tested at 100 kHz, 0.1 Vrms using an
Agilent/HP 4192A. Inductance at 1 MHz is the same for
parts with SRF ≥10 MHz.
3. DCR measured on a micro-ohmmeter.
4. SRF measured using Agilent/HP 8753ES or equivalent.
5. DC current at 25°C that causes the specified induc-
tance drop from its value without current.
Click for temperature derating information.
6. Current that causes the specified temperature rise from
25°C ambient. This information is for reference only and
does not represent absolute maximum ratings.
Click for temperature derating information.
7. Electrical specifications at 25°C.
Refer to Doc 362 “Soldering Surface Mount Components”
before soldering.
US [phone] [e-mail]
UK [phone] [e-mail]
Taiwan [phone] [e-mail]
China [phone] [e-mail]
Singapore + 65-6484 8412 [e-mail]
Document 536-1  Revised 09/02/15
© Coilcraft Inc. 2016
This product may not be used in medical or high
risk applications without prior Coilcraft approval.
Specification subject to change without notice.
Please check web site for latest information.