LPS3015 Datasheet, PDF (1/2 Pages) Coilcraft lnc. – Shielded Power Inductors

Document 436-1
Shielded Power Inductors – LPS3015
• Very low DCR; excellent current handling
• Miniature 3.0 × 3.0 mm footprint; less than 1.5 mm tall
Core material Ferrite
Core and winding loss  See www.coilcraft.com/coreloss
Environmental  RoHS compliant, halogen free
Terminations  RoHS compliant matte tin over nickel over silver.
Other terminations available at additional cost.
Weight  40 – 45 mg
Ambient temperature  –40°C to +85°C with (40°C rise) Irms current.
Maximum part temperature  +125°C (ambient + temp rise). Derating.
Storage temperature  Component: –40°C to +125°C.
Tape and reel packaging: –40°C to +80°C
Resistance to soldering heat  Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Moisture Sensitivity Level (MSL)  1 (unlimited floor life at <30°C /
85% relative humidity)
Failures in Time (FIT) / Mean Time Between Failures (MTBF)
38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332
Packaging  1000/7″ reel; 3500/13″ reel; Plastic tape:  12 mm wide,
0.26 mm thick, 8 mm pocket spacing, 1.65 mm pocket depth
Recommended pick and place nozzle  OD: 3 mm;  ID: ≤ 1.5 mm
PCB washing  Tested to MIL-STD-202 Method 215 plus an additional
aqueous wash. See Doc787_PCB_Washing.pdf.

DCR SRF
  _{Isat (A)}5 _{    Irms (A)}6
^  Inductance^{2  } max^{3  } typ⁴ 10% 20% 30% 20°C 40°C
  _{Part number}1 _{±20% (µH) (Ohms) (MHz) drop drop drop rise rise}
LPS3015-102MR_  1 .0
LPS3015-152MR_  1 .5
LPS3015-182MR_  1 .8
LPS3015-222MR_  2 .2
LPS3015-332MR_  3 .3
0.075 190 2.4 2.4 2.5 1.4 2.0
0.100 140 2.2 2.2 2.3 1.3 1.7
0.100 135 2.1 2.1 2.3 1.1 1.4
0.110 110 2.0 2.1 2.1 1.1 1.4
0.130 90 1.4 1.5 1.5 1.0 1.4
LPS3015-472MR_  4 .7
LPS3015-682MR_   6.8
LPS3015-103MR_  10
LPS3015-153MR_  15
LPS3015-183MR_  18
0.200
0.300
0.440
0.700
0.750
79 1.1 1.2 1.2 0.90 1.2
58 0.83 0.86 0.89 0.68 0.90
48 0.60 0.69 0.73 0.55 0.75
35 0.58 0.61 0.62 0.44 0.59
33 0.56 0.58 0.59 0.43 0.58
LPS3015-223MR_  22
LPS3015-333MR_  33
LPS3015-473MR_  47
LPS3015-683MR_  68
LPS3015-104MR_ 100
0.825
1.30
1.55
2.35
3.40
30 0.48 0.49 0.50 0.42 0.57
23 0.39 0.41 0.42 0.35 0.48
17 0.36 0.38 0.39 0.30 0.40
14 0.29 0.30 0.31 0.25 0.33
11 0.24 0.25 0.26 0.19 0.26
LPS3015-124MR_ 120
LPS3015-154MR_ 150
LPS3015-184MR_ 180
LPS3015-224MR_ 220
4.65
9.0 0.21 0.22 0.22 0.17 0.23
6.25
8.0 0.19 0.20 0.20 0.15 0.20
8.60
7.5 0.16 0.17 0.17 0.13 0.175
9.50
6.0 0.15 0.16 0.16 0.11 0.155
Coilcraft Designer’s Kit C392 contains samples of 0.80 µH to 33 µH parts (3 each)
from LPS3008, LPS3010 and LPS3015. Kit C401 contains samples of 0.56 µH to
33 µH parts (3 each) from LPS4012 and LPS4018. Kit C402 contains samples of
220 µH to 3300 µH parts (3 each) from all five series. For details of kit contents and
to order, contact Coilcraft or visit http://order.coilcraft.com.
1. Please specify termination and packaging codes:
LPS3015-333MRC
Termination: R= RoHS compliant matte tin over nickel
over silver.
Special order, added cost:
Q = RoHS tin-silver-copper (95.5/4/0.5)
or P = non-RoHS tin-lead (63/37).
Packaging: C= 7″ machine-ready reel. EIA-481
embossed plastic tape (1000 parts
per full reel).
B= Less than full reel. In tape, but not
machine ready. To have a leader and
trailer added ($25 charge), use code
letter C instead.
D= 13″ machine-ready reel. EIA-481
embossed plastic tape. Factory order
only, not stocked (3500 per full reel).
2. Inductance tested at 100 kHz, 0.1 Vrms using an
Agilent/HP 4192A. Inductance at 1 MHz is the same for
parts with SRF ≥10 MHz.
3. DCR measured on a micro-ohmmeter.
4. SRF measured using Agilent/HP 8753ES or equivalent.
5. DC current at 25°C that causes the specified induc-
tance drop from its value without current.
Click for temperature derating information.
6. Current that causes the specified temperature rise
from 25°C ambient. This information is for reference
only and does not represent absolute maximum rat-
ings. Click for temperature derating information.
7. Electrical specifications at 25°C.
Refer to Doc 362 “Soldering Surface Mount Components”
before soldering.
US [phone] [e-mail]
UK [phone] [e-mail]
Taiwan [phone] [e-mail]
China [phone] [e-mail]
Singapore + 65-6484 8412 [e-mail]
Document 436-1  Revised 09/02/15
© Coilcraft Inc. 2016
This product may not be used in medical or high
risk applications without prior Coilcraft approval.
Specification subject to change without notice.
Please check web site for latest information.