LPS3015-102ML Datasheet, PDF (1/2 Pages) Coilcraft lnc. – Shielded Power Inductors

Document 436-1
Shielded Power Inductors – LPS3015 Series
• Very low DCR; excellent current handling
• Miniature 3.0 × 3.0 mm footprint; less than 1.5 mm tall
Core material Ferrite
Core and winding loss See www.coilcraft.com/coreloss
Terminations RoHS compliant silver-palladium-platinum-glass frit.
Other terminations available at additional cost.
Weight 40 – 45 mg
Ambient temperature –40°C to +85°C with Irms current, +85°C to
+125°C with derated current
Storage temperature Component: –40°C to +125°C.
Packaging: –40°C to +80°C
Resistance to soldering heat Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C /
85% relative humidity)
Failures in Time (FIT) / Mean Time Between Failures (MTBF)
38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332
Packaging 1000/7″ reel; 3500/13″ reel; Plastic tape: 12 mm wide,
0.26 mm thick, 8 mm pocket spacing, 1.65 mm pocket depth
Recommended pick and place nozzle OD: 3 mm; ID: ≤ 1.5 mm
PCB washing Only pure water or alcohol recommended
DCR SRF
Isat (A)⁵
Inductance² max³ typ⁴ 10% 20% 30%
Part number¹ ±20% (µH) (Ohms) (MHz) drop drop drop
LPS3015-102ML_
1.0
0.075 190 1.8 2.0 2.1
LPS3015-152ML_
1.5
0.100 140 1.8 2.1 2.2
LPS3015-182ML_
1.8
0.100 135 1.5 1.7 2.1
LPS3015-222ML_
2.2
0.110 110 2.0 2.0 2.1
LPS3015-332ML_
3.3
0.130 90 1.4 1.5 1.5
LPS3015-472ML_
4.7
LPS3015-682ML_
6.8
LPS3015-103ML_ 10
LPS3015-153ML_ 15
LPS3015-183ML_ 18
0.200
0.300
0.440
0.700
0.750
79 1.1 1.2 1.2
58 0.83 0.86 0.89
48 0.60 0.69 0.73
35 0.58 0.61 0.62
33 0.56 0.58 0.59
LPS3015-223ML_ 22
LPS3015-333ML_ 33
LPS3015-473ML_ 47
LPS3015-683ML_ 68
LPS3015-104ML_ 100
0.825
1.30
1.55
2.35
3.40
30 0.48 0.49 0.50
23 0.39 0.41 0.42
17 0.36 0.38 0.39
14 0.29 0.30 0.31
11 0.24 0.25 0.26
LPS3015-124ML_ 120
LPS3015-154ML_ 150
LPS3015-184ML_ 180
LPS3015-224ML_ 220
LPS3015-334ML_ 330
4.65
6.25
8.60
9.50
23.0
9.0 0.21 0.22 0.22
8.0 0.19 0.20 0.20
7.5 0.16 0.17 0.17
6.0 0.15 0.16 0.16
5.0 0.10 0.11 0.11
Irms (A)⁶
20°C 40°C
rise rise
1.4 2.0
1.3 1.7
1.1 1.4
1.1 1.4
1.0 1.4
0.90 1.2
0.68 0.90
0.55 0.75
0.44 0.59
0.43 0.58
0.42 0.57
0.35 0.48
0.30 0.40
0.25 0.33
0.19 0.26
0.17 0.23
0.15 0.20
0.13 0.175
0.11 0.155
0.070 0.095
1. Please specify termination and packaging codes:
LPS3015-333MLC
Termination: L = RoHS compliant silver-palladium-
platinum-glass frit.
Special order: T = RoHS tin-silver-
copper (95.5/4/0.5) or S = non-RoHS tin-
lead (63/37).
Packaging: C= 7″ machine-ready reel. EIA-481
embossed plastic tape (1000 parts
per full reel).
B= Less than full reel. In tape, but not
machine ready. To have a leader and
trailer added ($25 charge), use code
letter C instead.
D= 13″ machine-ready reel. EIA-481
embossed plastic tape. Factory order
only, not stocked (3500 per full reel).
2. Inductance tested at 100 kHz, 0.1 Vrms using an
Agilent/HP 4192A. Inductance at 1 MHz is the same for
parts with SRF ≥10 MHz.
3. DCR measured on a micro-ohmmeter.
4. SRF measured using Agilent/HP 8753ES or equivalent.
5. DC current that causes the specified inductance drop
from its value without current.
6. Current that causes the specified temperature rise from
25°C ambient.
7. Electrical specifications at 25°C.
Refer to Doc 362 “Soldering Surface Mount Components”
before soldering.
Coilcraft Designer’s Kit C392 contains samples of 0.80 µH to 33 µH parts (3 each)
from LPS3008, LPS3010 and LPS3015. Kit C401 contains samples of 0.56 µH to
33 µH parts (3 each) from LPS4012 and LPS4018. Kit C402 contains samples of
220 µH to 3300 µH parts (3 each) from all five series. For details of kit contents and to
order, contact Coilcraft or visit http://order.coilcraft.com.
© Coilcraft, Inc. 2009
Specifications subject to change without notice.
Please check our website for latest information.
Document 436-1 Revised 08/05/09