XC6219 Datasheet, PDF (7/18 Pages) Torex Semiconductor – High Speed LDO Regulators Low ESR Cap Compatible ON/OFF Switch

XC6219 SERIES
ELECTRICAL CHARACTERISTICS
XC6219B series
Ta=25^OC
PARAMETER
SYMBOL
CONDITIONS
MAX.
TYP.
MIN.
UNITS CIRCUIT
Output Voltage
Maximum Output Current
Load Regulation
VOUT(E)
IOUTMAX
UVOUT
IOUT=30mA
1mA<IOUT<100mA
x 0.98 VOUT(T) x 1.02
V
1
150
-
-
mA
1
-
15
50
mV
1
Dropout Voltage
Supply Current
Standby Current
Line Regulation
Vdif1
Vdif2
IDD
Istby
UVOUT/
UVIN VOUT
IOUT=30mA
IOUT=100mA
VCE=VIN
VCE=VSS
VOUT(T)+1.0V<VIN<7.0V
IOUT=30mA
E-1
mV
1
E-2
mV
-
25
50
µA
2
-
0.01
0.10
µA
2
-
0.01
0.20
%/V
1
Input Voltage
Output Voltage Temperature
Characteristics
Ripple Rejection Rate
Current Limiter
Short Circuit Current
EN ‘High’ Voltage
EN ‘Low’ Voltage
EN ‘High’ Current
EN ‘Low’ Current
VIN
UVOUT/
UTopr VOUT
PSRR
Ilim
Ishort
VCEH
VCEL
ICEH
ICEL
IOUT=30mA
-40^OC<Topr<85^OC
IOUT=50mA, f=10kHz
VCE=VIN
VCE=VSS
2.0
-
100
-
65
-
300
-
50
1.60
-0.10
-0.10
6.0
V
-
-
ppm/^OC
1
-
dB
4
-
mA
1
-
mA
1
VIN
V
1
0.25
V
2
0.10
µA
2
0.10
µA
2
NOTE:
*1: VOUT(T) = Specified output voltage
*2: VOUT(E) = Effective output voltage (I.e. the output voltage when "VOUT(T)+1.0V" is provided at the VIN pin while maintaining a certain IOUT value.)
3: Vdif={VIN1^(*5)-VOUT1^(*4) }
*4: VOUT=A voltage equal to 98% of the output voltage whenever an amply stabilized IOUT {VOUT(T)+1.0V} is input.
*5: VIN=The Input Voltage when VOUT appears as Input Voltage is gradually decreased.
*6: Unless otherwise stated, VIN=VOUT(T)+1.0V.
DROPOUT VOLTAGE CHART
SYMBOL
E-1
Vdif1
E-2
Vdif2
PARAMETER
OUTPUT VOLTAGE
MIN.
TYP.
MAX.
MIN.
TYP.
MAX.
0.9
1100
1100
1110
1100
1150
1200
1.50
500
500
510
500
550
600
1.80 ~ 1.85
200
200
210
200
300
400
1.90 ~ 1.95
100
120
150
100
280
380
2.00 ~ 2.05
-
80
120
-
240
350
2.10 ~ 2.25
-
80
120
-
240
330
2.30 ~ 2.45
-
80
120
-
240
310
2.50 ~ 2.75
-
70
100
-
220
290
2.80 ~ 2.95
-
70
100
-
220
270
3.00 ~ 3.05
-
60
90
-
200
270
3.10 ~ 3.95
-
60
90
-
200
250
4.00 ~ 4.95
-
60
80
-
180
230
5.00
-
50
70
-
160
210
* The input voltage 2.0V (MIN) is needed to operate the series.
When the output voltage is less than 2.0V, 2.0V-VOUT(T) of dropout voltage is needed at minimum.
[e-mail]
www.zpsemi.com
7 of 18