GBU602H Datasheet, PDF (1/2 Pages) Zowie Technology Corporation – GLASS PASSIVATED BRIDGE RECTIFIER

GBU602H THRU GBU610H
GLASS PASSIVATED BRIDGE RECTIFIER
Reverse Voltage - 200 to 1000 Volts
Forward Current - 6.0 Amperes
GBU
0.224 (5.70)
0.209 (5.30)
0.311 (7.20)
0.268 (6.80)
0.878 (22.30)
0.854 (21.70)
0.118 (3.0) x 45^O
CHAMFER
0.146 (3.70)
0.130 (3.30)
0.142 (3.6)
0.103 (2.61)
0.087 (2.21)
0.728 (18.50)
0.689 (17.50)
0.098 (2.50)
0.059 (1.50)
0.053 (1.34)
0.037 (0.94)
0.208(5.28) 0.208(5.28) 0.208(5.28)
0.192(4.88) 0.192(4.88) 0.192(4.88)
0.047 (1.20)
0.031 (0.80)
0.028 (0.70)
0.012 (0.30)
Polarity shown on front side of case, positive lead by beveled corner
*Dimensions in inches and (millimeters)
FEATURES
* Halogen-free type
* Glass passivated chip junctions
* Compliance to RoHS product
* Plastic Material has Underwriters Laboratory Flammability
Classification 94V-0
* High surge current capability
* Ideal for Printed Circuit Boards
* High temperature soldering guaranteed : 260^oC/10 seconds
MECHANICAL DATA
Case : Molded Plastic
Terminals : Tin Plated, solderable per
MIL-STD-750, Method 2026
Polarity : As marked on Body
Weight : 4.0 grams (approx)
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Ratings at 25 ^oC ambient temperature
unless otherwise specified.
SYMBOLS GBU602H GBU604H GBU606H GBU608H
Maximum repetitive peak reverse voltage
VRRM
200
400
600
800
Maximum RMS voltage
VRMS
140
280
420
560
Maximum DC blocking voltage
VDC
200
400
600
800
Maximum average forward
rectified current )Tc=100^oC (NOTE1,2)
I (AV)
6.0
Peak forward surge current 8.3ms single half sine-wave
IFSM
175
superimposed on rated load (JEDEC Method)
GBU610H UNITS
1000
700
1000
Volts
Volts
Volts
Amps
Amps
Maximum instantaneous forward voltage at 3.0 A
VF
1.0
Maximum DC reverse current
@TA=25^oC
5
at rated DC blocking voltage
@TA=125^oC
IR
500
Typical Junction Capacitance per element (NOTE 4)
CJ
50
Typical thermal resistance per leg (NOTE 3)
R JA
7.4
R JC
2.2
Operating junctionStorage temperature range
TJ,TSTG
NOTES : (1) Unit case mounted on Al plate heat-sink
(2) Unit mounted on P.C.B. without heat-sink
(3) Recommended mounting position is to bolt down on heatsink with silicone thermal compound for
maximum heat transfer with #6 screw heat-sink size : 6.35 x 3.5 x 0.15cm)
(4) Measured at 1.0MHz and applied reverse voltage of 4.0V DC.
-55 to +150
Volts
uA
pF
o_{C / W}
o_C
REV. 0
Zowie Technology Corporation