|
YDA135 Datasheet, PDF (1/22 Pages) YAMAHA CORPORATION – STEREO 5W-20W DIGITAL AUDIO POWER AMPLIFIER CONTROLLER | |||
|
YDA135
D-20
STEREO 5W-20W DIGITAL AUDIO POWER AMPLIFIER CONTROLLER
Outline
YDA135 is digital audio power amplifier controller IC that is output power of 20W/channel on a 12V power supply
operation.
This IC is combined with the general purpose Power MOSFET (hereafter called Power MOSFET) that are
connected through BTL can configure an audio power amplifier with output power of 5W or 20W.
This IC accepts analog signal, converts it into digital pulse signal by the digital modulation circuitry and outputs
the digital pulse signal for driving Power MOSFET. The Power MOSFET that is driven by this IC outputs large
current digital pulses. The digital pulse signal is converted to audio signal through an external low pass filter, and
sent to the speakers.
By using a general purpose Power MOSFET, very low cost digital amplifier system is configured. By adapting
Yamaha's proprietary modulation system, the device provides low distortion and high signal to noise ratio at the
highest level among digital amplifiers in the equiralent class.
This IC has the overcurrent detection function that detects overcurrent state by voltage drop of external resistors
that detects the output current.
This IC has the high temperature detection function that detects high temperature by resistor value change of
external element that detects temperature.
The operation of this IC is limited by using two control signal, SLEEP or MUTE. SLEEP signal stops all functions
of this IC, and restrain to the power consumption at the minimum. MUTE signal brings Power MOSFET into
nonconductive state, and mute the output of the device.
This IC is configured by two power supply ; 5V for signal processing circuits, and 12V for Power MOSFET driving
circuits.
Features
ã»High
output
power
ãã20W
ï¼
VDDP=12.0V
RL=4Ω
THD+N<10%
ã»High
efficiency
operation
ãã80
%
ï¼
VDDP=12.0V
RL=4Ω
Po=20W
ãã85
%
ï¼
VDDP=12.0V
RL=8Ω
Po=10W
ã»Low
distortion(THD+N)
ãã0.03
%
ï¼
1kHz
RL=4Ω
Po=7W
ã»High
signal
to
noise
ratio
ãã100
dB
ï¼
VDDP=12.0V
Input
sensitivity1.0V
RL=4Ω
ãã97
dB
ï¼
VDDP=12.0V
Input
sensitivity150mV
RL=4Ω
ã»Low
consumption
current
(12V/5V
power
supply)
When
Power
MOSFET
(FW332)
is
connected.
ãã30mA
/7mA
ï¼
VDDP=12.0V
no
signal
ãã0.1mA/7mA
ï¼
VDDP=12.0V
at
mute
ãã
1μA/1μA
ï¼
VDDP=12.0V
at
sleep
ã»CS(Channel
separation)
ãã80
dB
ï¼
1kHz
ã»Any
gain
setting
by
external
resistors
ã»Sleep
function
by
SLEEP
terminal
ã»Output
mute
function
by
MUTE
terminal
ã»Over
current
detection
function
(Power
supply
short-circuiting,
Ground
short-
circuiting,
Load
short-circuiting)
ã»High
temperature
detection
function
ã»Pop
noise
suppression
function
at
turn-on
and
turn-off
ã»48-pin
plastic
LQFP
(YDA135-VZ)
YDA135CATALOG
CATALOG No.:LSI-4DA135A2
2003.3
|
▷ |