|
JCM15 Datasheet, PDF (1/2 Pages) – | |||
|
15/20 Watts
JCM Series
xppower.com
⢠Very High Power Density
⢠2:1 Input Range
⢠Operating Temperature 40 °C to +105 °C
⢠Single & Dual Outputs
⢠1600 VDC Isolation
⢠High Efficiency up to 89%
⢠3 Year Warranty
Specification
Input
Input Voltage Range
Input Current
Input Filter
Input Reflected
Ripple Current
Input Surge
⢠12 V (9-18 VDC)
24 V (18-36 VDC)
48 V (36-75 VDC)
⢠See table
⢠Pi network
⢠JCM15: 20 mA pk-pk, JCM20: 30 mA pk-pk
through 12 µH inductor and 47 µF
capacitor, 5 Hz to 20 MHz
⢠12 V models: 36 VDC for 100 ms
24 V models: 50 VDC for 100 ms
48 V models: 100 VDC for 100 ms
Output
Output Voltage
⢠See table
Output Trim
⢠±10% max on single output
Minimum Load
⢠No minimum load required
Initial Set Accuracy ⢠±1% max
Start Up Delay
⢠20 ms typical
Line Regulation
⢠JCM15: ±0.2% max, JCM20: ±0.5%
Load Regulation
⢠±0.5% max single, ±1.0% max dual
Cross Regulation
⢠±5% on dual output models (see note 2)
Transient Response
⢠<3% max deviation, recovery to within 1%
in 250 µs for a 25% load change
Ripple & Noise
⢠100 mV pk-pk, 20 MHz bandwidth,
(see note 3)
Overvoltage Protection ⢠3.3 V models: 3.9 V typical
5 V models: 6.2 V typical
12 V models: 15 V typical
15 V models: 18 V typical
±5 V models: ±6.2 V typical
±12 V models: ±15 V typical
±15 V models: ±18 V typical
Overload Protection ⢠150% of full load typical
Short Circuit Protection ⢠Trip & restart (hiccup) with auto recovery
Maximum Capacitive ⢠See table
Load
Temperature
Coefficient
⢠±0.02/°C max
Remote On/Off
⢠On >3.0 VDC or open circuit
Off <1.2 VDC or short circuit pins 2 & 3
General
Efficiency
Isolation
Isolation Capacitance
Switching Frequency
Power Density
MTBF
⢠See table
⢠1600 VDC Input to Output
1600 VDC Input to Case
1600 VDC Output to Case
⢠JCM15: 1200 pF max,
JCM20: 1000 pF max
⢠JCM15: 375 kHz typical,
JCM20: 330 kHz typical
⢠JCM15: 38.4 W/in3,
JCM20: 51.3 W/in3
⢠>560 kHrs to MIL-STD-217F at 25 °C, GB
Environmental
Operating Temperature ⢠-40 °C to +105 °C, derate from 100%
load at +65 °C to no load at +105 °C
for JCM15 and 100% load at +55 °C to
no load at 105 °C for JCM20
Case Temperature
⢠+105 °C max
Storage Temperature ⢠-40 °C to +125 °C
Humidity
⢠Up to 90%, non-condensing
Cooling
⢠Natural convection
EMC
Emissions
ESD Immunity
Radiated Immunity
EFT/Burst
Surge
Conducted Immunity
Magnetic Field
⢠EN55022 class A conducted & radiated
with external components, see application
note
⢠EN61000-4-2, 6 kV contact discharge,
8 kV air discharge, Perf Criteria A
⢠EN61000-4-3, 10 V/m, Perf Criteria A
⢠EN61000-4-4, level 2, Perf Criteria A*
⢠EN61000-4-5, level 2, Perf Criteria A
⢠EN61000-4-6, 10 Vrms, Perf Criteria A
⢠EN61000-4-8, 1 A/m, Perf Criteria A
*External input capacitor required, 220 µF/100 V.
|
▷ |