HDS800 Datasheet, PDF (1/4 Pages) XP Power Limited – 1U Profile, High Power Density

800 Watts
HDS800 Series
xppower.com
• High Efficiency up to 92%
• 1U Profile, High Power Density
• Programmable Output Voltage (0-105%)
• Programmable Output Current (0-105%)
• Parallel Operation
• Fully Featured Signals & Controls
• 3 Year Warranty
Specification
Input
General
Input Voltage
Input Frequency
Input Current
Inrush Current
Power Factor
Earth Leakage Current
Input Protection
• 90-264 VAC (127-370 VDC),
see derating curve
• 47-63 Hz
• 9.3 A/3.7 A typical at 100/240 VAC
• 30.0 A/60.0 A typical at 115/230 VAC
• 0.98/0.95, typical at 115/230 VAC full load
• <1.0 mA at 264 VAC/60 Hz
• T or F15 A/250 V internal fuse
Output
Efficiency
Isolation
Switching Frequency
Power Density
Signals & Controls
MTBF
• See model table
• 3000 VAC Input to Output,
1500 VAC Input to Ground,
500 VAC Output to Ground
• PFC 65 kHz typical, PWM 40-200 kHz
variable
• 10.1 W/in³
• Enable, Current Share, V Program,
I Program, 5 V Standby, PWM switching
• 90 kHrs to MIL-HDBK-217F at 25 ˚C
Output Voltage
• See model table
Output Trim
• ±5.0% by potentionmeter
Output Voltage Program • 0-105% of rated output
Output Current Program • 0-105% of rated output
Initial Set Accuracy • ±1%
Minimum Load
• No minimum load required
Start Up Delay
• 800 ms maximum
Start Up Rise Time
• 100 ms maximum at full load
Hold Up Time
• 8 ms minimum
Line Regulation
• ±1%
Load Regulation
• V1: ±1%, standby output: ±3%
Environmental
Operating Temperature • -20 ˚C to 70 ˚C, derate linearly from 100%
load at 50 ˚C to 50% load at 70 ˚C
Cooling
• Internal fan fitted. Speed increases with load
and internal temperature
Operating Humidity • 20-90% R.H. non-condensing
Storage Temperature • -40 ˚C to +85 ˚C
Storage Humidity
• 10-95% R.H.
Vibration
• 10-500 Hz, 2g 10 min/cycle, 60 min
period for each axis. Compliant to
IEC68-2-16, IEC 68-2-64
Transient Response
Ripple & Noise
• <1% for a 25% step load change
• 150 mV pk-pk all voltages, see note 1
EMC & Safety
Overvoltage Protection • Tracks output voltage. See application
notes, Recycle AC to reset
Emissions
Harmonic Currents
• EN55022 class B conducted & radiated
• EN61000-3-2 class A
Overtemperature
Protection
Overload Protection
• Primary and secondary heatsinks monitored. Voltage Flicker
Output shuts down, auto recovers
ESD Immunity
• >105% rated power, constant current
• EN61000-3-3
• EN61000-4-2, ±4 kV contact,
±8 kV air discharge, Perf Criteria A
Short Circuit Protection • Auto recovery
Radiated Immunity
• EN61000-4-3, 3 V/m, Perf Criteria A
Temperature
Coefficient
Remote Sense
• ±0.02%/˚C (0-50 ˚C)
• Compensates for 0.5 V max voltage drop
If remote sense is not required, local sense
must be used
EFT/Burst
Surge
Conducted Immunity
Magnetic Field
• EN61000-4-4, level 2, Perf Criteria A
• EN61000-4-5, installation class 3,
Perf Criteria A
• EN61000-4-6, 3 V, Perf Criteria A
• EN61000-4-8, 1 A/m, Perf Criteria A
Enable
Current Share
• Output must be enabled. See application
notes, power supply is shipped with enable
links fitted
• 5 supplies can share within 5%
Dips & Interruptions
Safety Approvals
• EN55024, >95% 10 ms, 30% 500 ms,
>95% 5000 ms, Perf Criteria A, A, B
• UL60950-1, CSA C22.2 No. 60950-1,
EN60950-1
Standby Output
• 5 V at 0.5 A, present whenever AC is applied
(9V at 0.3A, user selectable, by connecting
‘VSET’, Pin 18 of CN2 to ‘GND’)