X25097 Datasheet, PDF (8/15 Pages) Xicor Inc. – 5MHz Low Power SPI Serial E 2 PROM with IDLock TM Memory

X25097
ABSOLUTE MAXIMUM RATINGS*
Temperature under Bias ................... –65°C to +135°C
Storage Temperature ....................... –65°C to +150°C
Voltage on any Pin with
Respect to V_SS ................................... –1V to +7V
D.C. Output Current.............................................. 5mA
Lead Temperature
(Soldering, 10 seconds).............................. 300°C
*COMMENT
Stresses above those listed under “Absolute Maximum
Ratings” may cause permanent damage to the device.
This is a stress rating only and the functional operation of
the device at these or any other conditions above those
indicated in the operational sections of this specification
is not implied. Exposure to absolute maximum rating con-
ditions for extended periods may affect device reliability.
RECOMMENDED OPERATING CONDITIONS
Temperature
Commercial
Industrial
Min.
0°C
–40°C
Max.
+70°C
+85°C
7038 FRM T04
Supply Voltage
X25097
X25097-2.7
X25097-1.8
Limits
4.5V to 5.5V
2.7V to 5.5V
1.8V to 3.6V
7038 FRM T05
D.C. OPERATING CHARACTERISTICS (Over the recommended operating conditions, unless otherwise specified.)
Limits
Symbol
Parameter
Min.
Max. Units
Test Conditions
I_CC1
V_CC Supply Current (Write)
3
mA SCK = V_CC x 0.1/V_CC x 0.9 @ 5MHz,
SO = Open, CS = V_SS
I_CC2
I_SB
I_LI
I_LO
V_IL⁽¹⁾
V_IH⁽¹⁾
V_CC Supply Current (Read)
400
µA SCK = V_CC x 0.1/V_CC x 0.9 @ 5MHz,
SO = Open, CS = V_SS
V_CC Supply Current (Standby)
1
µA CS = V_CC, V_IN = V_SS or V_CC
Input Leakage Current
10
µA V_IN = V_SS to V_CC
Output Leakage Current
10
µA V_OUT = V_SS to V_CC
Input LOW Voltage
–0.5 V_CC x 0.3 V
Input HIGH Voltage
V_CC x 0.7 V_CC + 0.5 V
V_OL1
V_OL2
Output LOW Voltage
Output LOW Voltage
0.4
V V_CC > 3.3V, I_OL = 2.1mA
0.4
V 2V < V_CC ≤ 3.3V, I_OL = 1mA
V_OL3
Output LOW Voltage
0.4
V V_CC ≤ 2V, I_OL = 0.5mA
V_OH1
V_OH2
Output HIGH Voltage
Output HIGH Voltage
V_CC – 0.8
V_CC – 0.4
V V_CC > 3.3V, I_OH = -1.0mA
V 2V < V_CC ≤ 3.3V, I_OH = -0.4mA
V_OH3
Output HIGH Voltage
V_CC – 0.2
V V_CC ≤ 2V, I_OH = -0.25mA
POWER-UP TIMING
7038 FRM T06
Symbol
Parameter
Min.
Max.
Units
t_PUR⁽²⁾
t_PUW⁽²⁾
Power-up to Read Operation
Power-up to Write Operation
1
ms
5
ms
7038 FRM T07
Notes: (1) V_IL Min. and V_IH Max. are for reference only and are not 100% tested.
(2) t_PUR and t_PUW are the delays required from the time V_CC is stable until the specified operation can be initiated. These parameters
are periodically sampled and not 100% tested.
8