X24C01A Datasheet, PDF (8/13 Pages) Xicor Inc. – Serial E2PROM

X24C01A
ABSOLUTE MAXIMUM RATINGS*
Temperature Under Bias .................. –65°C to +135°C
Storage Temperature ....................... –65°C to +150°C
Voltage on any Pin with
Respect to V_SS ............................... –1.0V to +7V
D.C. Output Current ............................................ 5 mA
Lead Temperature
(Soldering, 10 Seconds) ............................. 300°C
*COMMENT
Stresses above those listed under “Absolute Maximum
Ratings” may cause permanent damage to the device.
This is a stress rating only and the functional operation of
the device at these or any other conditions above those
indicated in the operational sections of this specification is
not implied. Exposure to absolute maximum rating condi-
tions for extended periods may affect device reliability.
RECOMMENDED OPERATING CONDITIONS
Supply Voltage
Limits
Temperature
Min.
Max.
X24C01A
4.5V to 5.5V
Commercial
0°C
70°C
X24C01A-3.5
3.5V to 5.5V
Industrial
–40°C
+85°C
X24C01A-3
3V ± 5.5V
Military
–55°C
+125°C
X24C01A-2.7
2.7V to 5.5V
3841 PGM T02
3841 PGM T03
D.C. OPERATING CHARACTERISTICS (Over recommended operating conditions unless otherwise specified)
Symbol
Parameter
Limits
Min.
Max.
Units
Test Conditions
l_CC1
I_CC2
I_SB(1)
I_SB(1)
I_LI
I_LO
V_lL(2)
V_IH(2)
V_OL
Power Supply Current
(read)
1
mA SCL = V_CC x 0.1/V_CC x 0.9 Levels
@ 100 KHz, SDA = Open, All Other
Inputs = GND or V_CC – 0.3V
Power Supply Current
(write)
2
mA SCL = V_CC x 0.1/V_CC x 0.9 Levels
@ 100 KHz, SDA = Open, All Other
Inputs = GND or V_CC – 0.3V
Standby Current
50
µA SCL = SDA = V_CC – 0.3V, All Other
Inputs = GND or V_CC, V_CC = 5.5V
Standby Current
30
µA SCL = SDA = V_CC – 0.3V, All Other
Inputs = GND or V_CC, V_CC= 3.3V + 10%
Input Leakage Current
10
µA V_IN = GND to V_CC
Output Leakage Current
10
µA V_OUT = GND to V_CC
Input Low Voltage
–1.0 V_CC x 0.3 V
Input High Voltage
V_CC x 0.7 V_CC + 0.5 V
Output Low Voltage
0.4
V I_OL = 3 mA
3841 PGM T04
CAPACITANCE T_A = 25°C, f = 1.0MHZ, V_CC = 5V
Symbol
Test
C_I/O(3)
C_IN(3)
Input/Output Capacitance (SDA)
Input Capacitance (A₀, A₁, A₂, SCL, WC)
Notes: (1) Must perform a stop command prior to measurement.
(2) V_IL min. and V_IH max. are for reference only and are not tested.
(3) This parameter is periodically sampled and not 100% tested.
Max.
8
6
Units
pF
pF
Conditions
V_I/O = 0V
V_IN = 0V
3841 PGM T06
8