English
Language : 

ISL76123 Datasheet, PDF (3/12 Pages) Xicor Inc. – Automotive Single Supply, SPDT Analog Switch
◁
ISL76123
Absolute Maximum Ratings
V+ to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 to 15V
Input Voltages
IN (Note 5) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 to ((V+) + 0.3V)
NO, NC (Note 5) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 to ((V+) + 0.3V)
Output Voltages
COM (Note 5) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 to ((V+) + 0.3V)
Continuous Current (Any Terminal) . . . . . . . . . . . . . . . . . . . . . . . . . . . 30mA
Peak Current NO, NC, or COM
(Pulsed 1ms, 10% Duty Cycle, Max) . . . . . . . . . . . . . . . . . . . . . . . . . 40mA
ESD Rating
Human Body Model (Tested per JESD22-A114E) . . . . . . . . . . . . . . . . 2kV
Machine Model (Tested per JESD22-A115-A) . . . . . . . . . . . . . . . . . 100V
Charged Device Model (Tested per JESD22-C101). . . . . . . . . . . . . . . 1kV
Latch Up (Tested per JESD-78B; Class 2, Level A) . . . . . . . . . . . . . . 100mA
Thermal Information
Thermal Resistance (Typical)
θJA (°C/W) θJC (°C/W)
6 Ld SOT-23 Package (Notes 6, 7) . . . . . . . 175
95
Maximum Junction Temperature (Plastic Package) . . . . . . . . . . . +150°C
Maximum Storage Temperature Range. . . . . . . . . . . . . . . . . -65°C to +150°C
Operating Conditions
Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-40°C to +105°C
CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product
reliability and result in failures not covered by warranty.
NOTES:
5. Signals on NC, NO, COM, or IN exceeding V+ or GND are clamped by internal diodes. Limit forward diode current to maximum current ratings.
6. θJA is measured with the component mounted on a high effective thermal conductivity test board in free air. See Tech Brief TB379 for details.
7. For θJC, the “case temp” location is taken at the package top center.
Electrical Specifications - 5V Supply Test Conditions: V+ = +4.5V to +5.5V, GND = 0V, VINH = 2.4V, VINL = 0.8V (Note 8), unless
otherwise specified. Boldface limits apply over the operating temperature range, -40°C to +105°C.
PARAMETER
TEST CONDITIONS
TEMP MIN
MAX
(°C) (Notes 9, 10) TYP (Notes 9, 10) UNITS
ANALOG SWITCH CHARACTERISTICS
Analog Signal Range, VANALOG
ON-Resistance, rON
Full
0
V+ = 4.5V, ICOM = 1.0mA, VNO or VNC = 3.5V (Figure 5) +25
-
Full
-
-
V+
V
23
34
Ω
25
40
Ω
rON Matching Between Channels, ΔrON V+ = 5V, ICOM = 1.0mA, VNO or VNC = 3.5V
+25
-
0.8
2
Ω
Full
-
1
4
Ω
rON Flatness, RFLAT(ON)
V+ = 5V, ICOM = 1.0mA, VNO or VNC = 1V, 2V, 3V (Note 11) Full
-
7
8
Ω
NO or NC OFF Leakage Current, INO(OFF) V+ = 5.5V, VCOM = 1V, 4.5V, VNO or VNC = 4.5V, 1V
or INC(OFF)
+25
-3
0.01
3
nA
Full
-5
-
5
nA
COM OFF Leakage Current, ICOM(OFF)
V+ = 5.5V, VCOM = 4.5V, 1V, VNO or VNC = 1V, 4.5V
+25
-3
-
3
nA
Full
-5
-
5
nA
COM ON Leakage Current, ICOM(ON)
V+ = 5.5V, VCOM = 1V, 4.5V, or VNO or VNC = 1V, 4.5V or +25
-5
-
5
nA
Floating
Full
-10
-
10
nA
DYNAMIC CHARACTERISTICS
Turn-ON Time, tON
VNO or VNC = 3V, RL = 1kΩ, CL = 35pF, VIN = 0V to 3V
+25
-
28
-
ns
(See Figure 1)
Full
-
40
-
ns
Turn-OFF Time, tOFF
VNO or VNC = 3V, RL = 1kΩ, CL = 35pF, VIN = 0V to 3V
+25
-
20
-
ns
(See Figure 1)
Full
-
30
-
ns
Break-Before-Make Time Delay, tD
RL = 300Ω, CL = 35pF, VNO = VNC = 3V, VIN = 0V to 3V
Full
-
10
-
ns
(See Figure 3)
Charge Injection, Q
OFF Isolation
Power Supply Rejection Ratio
NO or NC OFF Capacitance, COFF
CL = 1.0nF, VG = 0V, RG = 0Ω (See Figure 2)
RL = 50Ω, CL = 5pF, f = 1MHz (See Figure 4)
RL = 50Ω, CL = 5pF, f = 1MHz
f = 1MHz, VNO or VNC = VCOM = 0V (See Figure 7)
+25
-
3
-
pC
+25
-
76
-
dB
+25
-
60
-
dB
+25
-
8
-
pF
3
FN8297.1
September 28, 2012
 ▷