890334024003 Datasheet, PDF (7/8 Pages) Wurth Elektronik GmbH & Co. KG, Germany. – WCAP-FTXX Film Capacitors

I Cautions and Warnings:
The following conditions apply to all goods within the product series of WCAP-FTXX
of Würth Elektronik eiSos GmbH & Co. KG:
General:
The capacitor is engineered, designed and manufactured to be used within the data sheet specified values.
Do not use the capacitor neither short term nor long term outside the specified values, which are given in the data sheet.
Product specific:
Follow all instructions mentioned in the data sheet, especially:
•The soldering profile has to be complied with according to the technical reflow soldering specification, otherwise this will void the
warranty.
• Wave soldering is only allowed after evaluation and approval.
•Do not exceed the lower and/ or upper specified temperature!
•Do not use the capacitor with other than specified voltage!
•Prevent any kind of mechanical stress to the capacitor terminals!
•Do not use the soldered capacitor on a PCB for any movement or transportation to avoid any tensile force to the capacitor!
•Do not apply any kind of flexural or compressive force onto soldered or unsoldered component!
•Prevent the capacitor surface from any damage or scratches with sharp edges (e.g. chassis, screwdrivers, pincers)
•The capacitor must be placed on a PCB while using the recommended drill hole pattern without changing of the specific lead pitch!
•Avoid any other than specified temperature and / or time conditions during soldering!
•Avoid any overload or conditions that are not specified in the capacitors datasheet!
•Avoid any water or heavy dust on capacitors surface which may cause electrical leakage, damage, overheating or corrosion!
Storage conditions:
These film capacitors must be stored in stable climatic conditions, which are listed within the general information on front of data sheet.
Storage duration:
All products shall be used before the end of the period of 12 months based on the product date code, if not a 100% solderability can´t be en-
sured.
Flammability:
Avoid any external energy or open fire (passive flammability).
Vibration resistance:
Do not exceed the vibration limits given by IEC60068-2-6.
Cleaning:
Do not use any other cleaning solvents for box-typed capacitors except: ethanol, isopropanol, n-propanol - water mixtures. After cleaning a
drying process with temperatures not exceeding 65°C and not longer than 4 hours is mandatory to prevent any kind of electrical damage.
Full covered or embedded capacitors in final applications:
If final assemblies will be placed completely in any plastic resin, physical, chemical and thermal influences must be considered. If any specific
evaluation or test is necessary please contact the related Würth Elektronik Capacitor Business Division.
DESCRIPTION
WCAP-FTXX Film Capacitors
Würth Elektronik eiSos GmbH & Co. KG
1.3
2015-04-16
SSt
PSL
EMC & Inductive Solutions
Max-Eyth-Str. 1
1.2
2014-08-14
SSt
PSL
74638 Waldenburg
Germany
Order.- No.
SIZE
1.1
2014-05-20
SSt
1.0
2014-01-22
SSt
PSL
Tel. [phone] - 0
PSL
www.we-online.com
890334024003
A4
[e-mail]
REV
DATE
BY
CHECKED
Size: Pitch 12.5 mm - PL 20
This electronic component has been designed and developed for usage in general electronic equipment only. This product is not authorized for use in equipment where a higher safety standard and reliability standard is especially required or where a failure of the product is reasonably expected to cause severe personal injury or death, unless the parties have executed an agreement specifically governing such use.
Moreover Würth Elektronik eiSos GmbH & Co KG products are neither designed nor intended for use in areas such as military, aerospace, aviation, nuclear control, submarine, transportation (automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network etc.. Würth Elektronik eiSos GmbH & Co KG must be informed about the intent of such usage before
the design-in stage. In addition, sufficient reliability evaluation checks for safety must be performed on every electronic component which is used in electrical circuits that require high safety and reliability functions or performance.