0205200000 Datasheet, PDF (1/1 Pages) Weidmuller – Cable Lug 32/35 mm DIN-Rail Terminals

Cable Lug 32/35 mm
DIN-Rail Terminals
Feed Through
SAKG 28 I
SAKG 28 II
The Weidmuller SAKG range offers the following connection
variations:
• Clamping yoke connection, Version III. The stripped
conductor can be connected without further preparation.
• Lug connection, Version II.
Two types of screw connection are provided here.
a) Screw set with lock nut
b) with thread in the busbar
• Clamping yoke/lug connection as a combination, Version I.
Available Options
Version
KrG 0170020000
0170320000
Version I
Version II
without thread
Dimensions
Width / Length / Height mm (in.) with TS 35 x 7.5
with TS 32
Insulation stripping length
mm (in.)
Technical Data
Rated voltage / rated current / wire size
UL
CSA
VDE
–
28/70/63.5 (1.1/2.76/2.5)
15 (.59)
600 V / 95 A / #2 AWG
600 V / 110 A / #6…1 AWG
1000 VAC / 110 A / 35 mm²
–
28/70/53 (1.1/2.76/2.09)
–
600 V / 115 A / #2 AWG
600 V / 135 A / #8…2 AWG
1000 VAC / 110 A / 35 mm²
Torque
Nm (lb. in.)
Clamping screw
M
End Plate, Hard Paper (thickness mm)
For
Tropic-proof
22.6 (200.0)
6
Type
EP 1 (2)
EP 1 (2)
Part No.
0205100000
0205200000
22.6 (200.0)
6
Type
EP 1 (2)
EP 1 (2)
Part No.
0205100000
0205200000
Version II G
with thread
Version III
For
Tropic-proof
Cables with cable lugs are connected to
Version I SAKG terminals and SS stud terminals.
Fitting instructions for SAKG terminals
When tightening the clamping screw, it is recommended that the
conductor be held against the tightening direction in order to avoid
any deformation of the mounting rail and to keep the terminal foot
free of torsional forces.
Partition, Hard Paper (thickness mm)
Tropic-proof
TW 1 (2)
TW 1 (2)
Jumpers
Note: Final number in model indicates
no. of poles (e.g. QL 2 = 2 poles). For
additional information, see Accessories
section.
QL 2
QL 3
QL 4
0151400000 TW 1 (2)
0164600000 TW 1 (2)
0151400000
0164600000
0193900000
0407600000
0407700000
QL 2
QL 3
QL 4
0193900000
0407600000
0407700000
QL
Cover
AH 28
0326660000 AH 28
0326660000
Cover
In order to ensure shock protection following connection of the
conductors, Type AH hoods can be snapped onto the terminal.
Marking Tags
Print
Note: Part numbers shown are for a single _{Consecutive horizontal}
card of pre-printed tags numbered 1-50.
For additional information, see Accessories section. Consecutive vertical
DEK 5/5
DEK 5/5
0473460001 DEK 5/5
0473560001 DEK 5/5
0473460001
0473560001
See Accessories section for mounting rails, end brackets, test taps, additional marking material and accessories.
150