JFCW24S33-4000 Datasheet, PDF (2/4 Pages) Wall Industries,Inc. – Single & Dual Output 15 Watt DC/DC Converter 4:1 Ultra Wide Input Voltage Range

Rev. B 4/16/2008
JFCW Series
Single & Dual Output
15 Watt DC/DC Converter
4:1 Ultra Wide Input Voltage Range
SAFETY & EMC
Approvals and Standards................. IEC60950-1, UL60950-1, EN60950-1
EMI (See Note 9) ............... EN55022............................................. Class A
ESD.................... EN61000-4-2…….. ^Air
± 8KV _{……Perf. Criteria B}
Contact ± 6KV
Radiated Immunity........... EN61000-4-3……………10V/m Perf. Criteria A
Fast Transient.................. EN61000-4-4…………….±2KV Perf. Criteria B
Surge (See Note 10)........ EN61000-4-5………….±0.5KV Perf. Criteria B
Conducted Immunity........ EN61000-4-6…………10 Vrms Perf. Criteria A
OUTPUT VOLTAGE / CURRENT RATING CHART
Model Number Input Range
Output
Voltage
Output
Current
Ripple & Noise⁽⁴⁾
Input Current
No Load⁽³⁾ Full Load⁽²⁾
JFCW24S3.3-4000
3.3 VDC
4000mA
75mVp-p
50mA
688mA
JFCW24S5-3000
5 VDC
3000mA
75mVp-p
50mA
782mA
JFCW24S12-1300
JFCW24S15-1000
JFCW24D05-1500
24VDC
(9 – 36 VDC)
12 VDC
15 VDC
± 5 VDC
1300mA
1000mA
±1500mA
100mVp-p
100mVp-p
100mVp
20mA
20mA
20mA
803mA
772mA
772mA
JFCW24D12-625
± 12 VDC
± 625mA
100mVp
25mA
753mA
JFCW24D15-500
± 15 VDC
± 500mA
100mVp
25mA
744mA
JFCW48S3.3-4000
3.3 VDC
4000mA
75mVp-p
40mA
336mA
JFCW48S5-3000
5 VDC
3000mA
75mVp-p
40mA
382mA
JFCW48S12-1300
JFCW48S15-1000
JFCW48D05-1500
48VDC
(18 – 75 VDC)
12 VDC
15 VDC
± 5 VDC
1300mA
1000mA
± 1500mA
100mVp-p
100mVp-p
100mVp
15mA
15mA
15mA
392mA
377mA
386mA
JFCW48D12-625
± 12 VDC
± 625mA
100mVp
15mA
382mA
JFCW48D15-500
± 15 VDC
± 500mA
100mVp
20mA
377mA
*****See Product Standard Table for suffix options*****
Efficiency⁽⁴⁾
86%
84%
86%
85%
85%
87%
88%
86%
86%
87%
87%
85%
86%
87%
Max Capacitor
Load⁽⁵⁾
1000uF
1000uF
330uF
220uF
500uF
150uF
100uF
1000uF
1000uF
330uF
220uF
500uF
150uF
100uF
NOTES
1. BELLCORE TR-NWT-000332. Case 1: 50% Stress, Temperature at 40ºC.
MIL-HDBK-217F Notice2 @Ta=25 ºC, Full load (Ground fixed and controlled environment).
2. Maximum value at nominal input voltage and full load.
3. Typical value at nominal input voltage and no load.
4. Typical value at nominal input voltage and full load.
5. Test by minimum Vin and constant resistive load.
6. Trimming allows the user to increase or decrease the output voltage set point of the module. This is accomplished by connecting an
external resistor between the TRIM pin and either the +Vout pin or the –Vout pin.
7. The ON/OFF control pin voltage is referenced to -Vin. (See the “Product Standard Table” below for suffix options).
8. Heat Sink is optional. Consult factory for ordering details.
9. The JFCW Series can meet EN55022 Class A with external capacitors connected in parallel to the input pins.
Recommended: 24Vin: 6.8uF/50V
48Vin: 2.2uF/100 * 2 pcs
10. An external filter capacitor is required if the module has to meet EN61000-4-5. The filter capacitor Wall Industries suggests: Nippon
chemi-con KY Series, 220µF/100V, ESR 48mΩ.
Wall Industries, Inc. 5 Watson Brook Road Exeter, NH 03833
603-778-2300 www.wallindustries.com Fax [phone]