PSAE800 Datasheet, PDF (1/8 Pages) Wall Industries,Inc. – AC/DC Switching Power Supplies

Wall Industries, Inc.
Rev B
PSAE800 SERIES
Up to 804 Watts, AC/DC Switching Power Supplies
Size:
9.80 x 5.00 x 1.61 inches
(249.0 x 127.0 x 41.0 mm)
FEATURES
• RoHS Compliant
• Active PFC > 0.95 at 230VAC
• Up to 804 Watts Output Power
• High Efficiency up to 93%
• 4242VDC I/O Isolation
• Constant Current Limiting
• Intelligent LED Indicators
• Optional RS232 Function
• Built-in I²C Serial Data Bus
• 1U Profile, High Power Density
• Protection: OLP, OVP, OTP, Fan Failure
• Programmable Output Voltage (0~105%)
• Programmable Output Current (0~105%)
• Power OK Signal (Power Good, Logic Low)
• Remote ON/OFF, Remote Sense Functions
• Universal Input Voltage Range: 90-264VAC
• Single Outputs Ranging from 12~60VDC
• +5V/0.5A or +8V/0.3A Auxiliary Output
Selectable by User
• Forced Current Sharing at Parallel Operation
• UL 60950-1, 2nd edition, TUV EN60950-1:
2006+A11 Approvals
DESCRIPTION
The PSAE800 series of AC/DC switching power supplies provides up to 804 Watts of output
power in a 9.80” x 5.00” x 1.61” enclosed case. This series consists of single output models
ranging from 12~60VDC with an input voltage range of 90~264VAC. Standard features
include high efficiency up to 93%, active PFC, programmable output voltage and output
current, remote on/off, remote sense, power OK signal, and internal ball bearing fan. This
series also has over voltage, over load, and over temperature protection. All models are
RoHS compliant and have UL 60950-1, 2nd edition and TUV EN60950-1: 2006+A11 safety
approvals.
Model Number
Input Voltage
MODEL SELECTION TABLE
Output Voltage Output Current Output Power Ripple & Noise ⁽¹⁾
Efficiency
PSAE-800-12
12 VDC
66.7A
800W
120mVp-p
89%
PSAE-800-15
15 VDC
53.4A
801W
150mVp-p
90%
PSAE-800-24
24 VDC
33.5A
804W
240mVp-p
92%
PSAE-800-30
90~264 VAC
30 VDC
26.7A
801W
300mVp-p
92%
PSAE-800-36
36 VDC
22.3A
802.8W
360mVp-p
92%
PSAE-800-48
48 VDC
16.7A
801.6W
480mVp-p
92%
PSAE-800-60
60 VDC
13.4A
804W
600mVp-p
93%
NOTES
1. Ripple & noise is measured at 20MHz limited bandwidth and using a 12" twisted pair-wire terminated with a 0.1µF & 47µF
capacitors in parallel.
2. For voltages near the low end of the input voltage range, see the derating curve for the power supply output rating.
3. When in parallel operation only one unit might operate if the total output load is less than 5% of the rated load condition.
4. The power supply is considered a component which will be installed into final equipment. The final equipment must be re-
confirmed that it still meets EMC directives.
07/23/2013
Wall Industries, Inc. • 37 Industrial Drive, Exeter, NH 03833 • Tel: [phone] • Toll Free: 888-597-9255 • Fax [phone]
website: www.wallindustries.com • e-mail: [e-mail]
Page 1 of 8