TNPU-E3 Datasheet, PDF (7/9 Pages) Vishay Siliconix – Ultra Precision Thin Film Chip Resistors

www.vishay.com
TNPU e3
Vishay Draloric
TEST PROCEDURES AND REQUIREMENTS
EN 60115-1 IEC 60068-2 ⁽¹⁾
CLAUSE TEST METHOD
TEST
PROCEDURE
REQUIREMENTS
PERMISSIBLE CHANGE (R)
Stability for product types:
TNPU0603 e3
TNPU0805 e3
TNPU1206 e3
4.19
4.13
14 (Na)
-
Rapid change
of temperature
Short time
overload
30 min at LCT and
30 min at UCT;
LCT = -55 °C;
UCT = 125 °C;
1000 cycles
U = 2.5 x P₇₀ x R
or U = 2 x U_max.;
whichever is the less severe;
5s
± (0.1 % R + 0.01 )
± (0.05 % R + 0.01 )
Endurance by sweeping;
10 Hz to 2000 Hz;
4.22
6 (Fc)
Vibration
no resonance;
amplitude  1.5 mm or
 200 m/s²; 6 h
± (0.05 % R + 0.01 )
no visible damage
Solder bath method;
SnPb40; non-activated flux
(215 ± 3) °C; (3 ± 0.3) s
4.17
58 (Td)
Solderability
Solder bath method;
Good tinning ( 95 % covered);
no visible damage
SnAg3Cu0,5 or SnAg3,5;
non-activated flux
(235 ± 3) °C; (2 ± 0.2) s
4.18
58 (Td)
Resistance to
soldering heat
Solder bath method;
(260 ± 5) °C; (10 ± 1) s
± (0.02 % R + 0.01)
4.29
45 (XA)
Component solvent
resistance
Isopropyl alcohol
+50 °C; method 2
No visible damage
RR 1608M; 9 N
4.32
21 (Ue₃)
Shear (adhesion)
RR 2012M and
RR 3216M; 45 N
No visible damage
4.33
21 (Ue₁)
Substrate bending
Depth 2 mm, 3 times
± (0.05 % R + 0.01)
no visible damage, no open circuit in bent position
4.7
-
Voltage proof
U_RMS = U_ins; 60 ± 5 s
No flashover or breakdown
4.35
-
Flammability
IEC 60 695-11-5 ⁽¹⁾,
needle flame test; 10 s
No burning after 30 s
4.39
-
Periodic electric
overload:
Standard operation
mode
U = 15 x P₇₀ x R
or U = 2 x U_max.;
whichever is the less severe;
0.1 s on; 2.5 s off;
1000 cycles
± (0.1 R + 0.02 )
4.37
67 (Cy)
Damp heat,
steady state,
accelerated
(85 ± 5) °C; 56 days
(85 ± 5) % RH
± (0.25 R + 0.05 )
IEC 61340-3-1 ⁽¹⁾;
3 pos. + 3 neg.
Electro static
(equivalent to MIL-STD-883,
4.38
-
discharge
method 3015)
(Human Body Model)
TNPU0603: 1000 V
TNPU0805: 1500 V
TNPU1206: 2000 V
± (0.5 R + 0.05 )
Note
(1) _{The quoted IEC standards are also released as EN standards with the same number and identical contents.}
Revision: 01-Jul-16
7
Document Number: 28779
For technical questions, contact: [e-mail]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000