RH025R2000 Datasheet, PDF (4/5 Pages) Vishay Siliconix – Wirewound Resistors, Industrial Power, Aluminum Housed, Chassis Mount

www.vishay.com
MATERIAL SPECIFICATIONS
Element: Copper-nickel alloy or nickel-chrome alloy,
depending on resistance value
Core: Ceramic, steatite or alumina, depending on physical
size
Encapsulant: Silicone molded construction
Housing: Aluminum with hard anodic coating
End Caps: Stainless steel
Standard Terminals: For RH005 through RH050 size
terminal finish - Tin/lead is 60/40 Sn/Pb w/Nickel underplate
and Lead (Pb)-free is Ni/Pd/Au, finish is on copper clad
steel core terminal. For RH100 and RH250 terminals are
threaded stainless steel.
Part Marking: Dale, model, wattage, value, tolerance, date
code
NH NON-INDUCTIVE
Models of equivalent physical and electrical specifications
are available with non-inductive (Ayrton-Perry) winding.
They are identified by substituting the letter N for R in the
model number (NH005, for example).
RH, NH
Vishay Dale
SPECIAL MODIFICATIONS
A number of special modifications to the aluminum housed
resistor style are available upon request. Special
modifications include:
• Terminal configurations and materials
• Resistance values and tolerances
• Low resistance temperature coefficient (RTC)
• Housing configuration
• Threaded mounting holes
• Preconditioning and other additional testing
APPLICABLE MIL SPECIFICATIONS
Vishay RH and NH resistors are listed as qualified on the
MIL-PRF-18546 QPL. MIL-PRF-18546 qualified, type RE
resistors can be found at: www.vishay.com/doc?30282



PERFORMANCE
TEST
Thermal Shock
Short Time Overload
Dielectric Withstanding 
Voltage
Temperature
Moisture Resistance
Shock, Specified Pulse
Vibration, High Frequency
Load Life
Terminal Strength
CONDITIONS OF TEST
Rated power applied until thermally stable, then a minimum of 15 min at - 55 °C
5 x rated power for 5 s
1000 V_rms for RH005, RH010 and RH025; 2000 Vrms for RH050;
4500 V_rms for RH100 and RH250; duration 1 min
250 °C for 2 h
MIL-STD-202 Method 106, 7b not applicable
MIL-STD-202 Method 213, 100 g’s for 6 ms, 10 shocks
Frequency varied 10 Hz to 2000 Hz, 20 g peak, 2 directions 6 h each
1000 h at rated power, + 25 °C, 1.5 h “ON”, 0.5 h “OFF”
30 s, 5 pound pull test for RH005 and RH010, 10 pound pull test for other sizes;
torque test - 24 pound inch for RH100 and 32 pound inch for RH250
TEST LIMITS
± (0.5 % + 0.05 ) R
± (0.5 % + 0.05 ) R
± (0.2 % + 0.05 ) R
± (0.5 % + 0.05 ) R
± (1.0 % + 0.05 ) R
± (0.2 % + 0.05 ) R
± (0.2 % + 0.05 ) R
± (1.0 % + 0.05 ) R
± (0.2 % + 0.05 ) R
Revision: 23-May-13
4
Document Number: 30201
For technical questions, contact: [e-mail]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000