DG411_11 Datasheet, PDF (4/14 Pages) Vishay Siliconix – Precision Monolithic Quad SPST CMOS Analog Switches

DG411, DG412, DG413
Vishay Siliconix
SPECIFICATIONS^a (for Unipolar Supplies)
Test Conditions
Parameter
Symbol
Unless Specified
V + = 12 V, V - = 0 V
V_L = 5 V, V_IN = 2.4 V, 0.8 V^f
Analog Switch
Analog Signal Range^e
V_ANALOG
Drain-Source
On-Resistance
R_DS(on)
V + = 10.8 V,
I_S = - 10 mA, V_D = 3 V, 8 V
Dynamic Characteristics
Turn-On Time
Turn-Off Time
Break-Before-Make
Time Delay
Charge Injection
Power Supplies
t_ON
R_L = 300 , C_L = 35 pF
t_OFF
V_S = 8 V, see figure 2
t_D
DG413 only, V_S = 8 V
R_L = 300 , C_L = 35 pF
Q
V_g = 6 V, R_g = 0 , C_L = 10 nF
Positive Supply Current
I+
Negative Supply Current
Logic Supply Current
Ground Current
I-
I_L
I_GND
V + = 13.5 V, V_IN = 0 V or 5 V
Temp.^b
Typ.^c
A Suffix
D Suffix
- 55 °C to 125 °C - 40 °C to 85 °C _Unit
Min.^d Max.^d Min.^d Max.^d
Full
Room
40
Full
12
12
V
80
100
80
100

Room 175
Hot
Room
95
Hot
Room
25
Room
25
250
250
400
315
125
140
125
140
ns
pC
Room 0.0001
1
1
Hot
5
5
Room - 0.0001 - 1
-1
Hot
-5
-5
µA
Room 0.0001
1
1
Hot
5
5
Room - 0.0001 - 1
Hot
-5
-5
Notes:
a.Refer to process option flowchart.
b.Room = 25 °C, Full = as determined by the operating temperature suffix.
c. Typical values are for DESIGN AID ONLY, not guaranteed nor subject to production testing.
d.The algebraic convention whereby the most negative value is a minimum and the most positive a maximum, is used in this data sheet.
e.Guaranteed by design, not subject to production test.
f. V_IN = input voltage to perform proper function.
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation
of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum
rating conditions for extended periods may affect device reliability.
TYPICAL CHARACTERISTICS (25 °C, unless otherwise noted)
50
45 ^{TA = 25 °C}
±5V
40
35
30
25
± 15 V
20
±8V
± 10 V
± 12 V
15
± 20 V
10
5
0
- 20 - 15 - 10 - 5 0 5 10 15 20
V_D - Drain V oltage (V)
On-Resistance vs. V_D and Power Supply Voltage
300
250
V+ = 3 V
V_L = 3 V
200
V_L = 5 V
150
V+ = 5 V
100
8V
50
12 V
15 V _{20 V}
0
0 2 4 6 8 10 12 14 16 18 20
V_D - Drain Voltage (V)
On-Resistance vs. V_D and Unipolar Supply Voltage
www.vishay.com
Document Number: 70050
4
S11-1185-Rev. G, 13-Jun-11
This document is subject to change without notice.
THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000