DG411_08 Datasheet, PDF (4/9 Pages) Vishay Siliconix – Precision Monolithic Quad SPST CMOS Analog Switches

DG411/412/413
Vishay Siliconix
SPECIFICATIONS FOR UNIPOLAR SUPPLIES^a
Parameter
Analog Switch
Symbol
Test Conditions
Unless Specified
V+ = 12 V, V- = 0 V
V_L = 5 V, V_IN = 2.4 V, 0.8 V^f
A Suffix
D Suffix
- 55 to 125 °C - 40 to 85 °C
Temp^b Typ^c Min^d Max^d Min^d Max^d Unit
Analog Signal Range^e
Drain-Source
On-Resistance
Dynamic Characteristics
Turn-On Time
Turn-Off Time
Break-Before-Make
Time Delay
Charge Injection
Power Supplies
V_ANALOG
r_DS(on)
t_ON
t_OFF
t_D
Q
V+ = 10.8 V,
I_S = - 10 mA, V_D = 3 V, 8 V
R_L = 300 Ω, C_L = 35 pF
V_S = 8 V, See Figure 2
DG413 Only, V_S = 8 V
R_L = 300 Ω, C_L = 35 pF
V_g = 6 V, R_g = 0 Ω, C_L = 10 nF
Full
Room 40
Full
Room 175
Hot
Room 95
Hot
Room 25
Room 25
12
12 V
80
100
80
100
Ω
250
250
400
315
125
125
140
140 ^ns
pC
Positive Supply Current
Negative Supply Current
Logic Supply Current
Ground Current
I+
I-
I_L
I_GND
V+ = 13.5 V, V_IN = 0 or 5 V
Room 0.0001
1
1
Hot
5
5
Room - 0.0001 - 1
-1
Hot
-5
-5
Room 0.0001
1
1
µA
Hot
5
5
Room - 0.0001 - 1
Hot
-5
-5
Notes:
a.Refer to PROCESS OPTION FLOWCHART.
b.Room = 25 °C, Full = as determined by the operating temperature suffix.
c. Typical values are for DESIGN AID ONLY, not guaranteed nor subject to production testing.
d.The algebraic convention whereby the most negative value is a minimum and the most positive a maximum, is used in this data sheet.
e.Guaranteed by design, not subject to production test.
f. V_IN = input voltage to perform proper function.
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation
of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum
rating conditions for extended periods may affect device reliability.
TYPICAL CHARACTERISTICS 25 °C, unless otherwise noted
50
45 ^{TA = 25 °C}
±5V
40
35
30
25
± 15 V
20
±8V
± 10 V
± 12 V
15
± 20 V
10
5
0
- 20 - 15 - 10 - 5 0
5 10 15 20
V_D – Drain Voltage (V)
On-Resistance vs. V_D and Power Supply Voltage
300
250
V+ = 3 V
V_L = 3 V
200
V_L = 5 V
150
V+ = 5 V
100
8V
50
12 V
15 V _{20 V}
0
0 2 4 6 8 10 12 14 16 18 20
V_D – Drain Voltage (V)
On-Resistance vs. V_D and Unipolar Supply Voltage
www.vishay.com
4
Document Number: 70050
S-71241–Rev. E, 25-Jun-07