DG2715_11 Datasheet, PDF (3/9 Pages) Vishay Siliconix – Low-Voltage, 0.4ohm RON, Single SPST Analog Switch

DG2715, DG2716
Vishay Siliconix
SPECIFICATIONS (V+ = 3.0 V)
Parameter
Analog Switch
Symbol
Test Conditions
Otherwise Unless Specified
V+ = 3 V, ± 10 %,V_IN = 0.5 V or 1.4 V^e
Temp.^a
Limits
- 40 °C to 85 °C
Min.^b Typ.^c Max.^b
Unit
Analog Signal Range^d
On-Resistance
R_ON Flatness
Switch Off Leakage Current
V_NO, V_NC,
V_COM
R_ON
R_ON
Flatness
I_NO(off)
I_NC(off)
I_COM(off)
V+ = 2.7 V, V_COM = 1.5 V
I_NO, I_NC = 100 mA
V+ = 2.7 V, V_COM = 0.6 V, 1.5 V, 2.1 V
I_NO, I_NC = 100 mA
V+ = 3.3 V,
V_NO, V_NC = 0.3 V/3 V, V_COM = 3 V/0.3 V
Full
0
Room
Full
0.4
Room
0.1
Room - 1
Full
- 10
Room - 1
Full
- 10
V+
V
0.6

0.2
1
10
1
nA
10
Channel-On Leakage Current
I_COM(on)
V+ = 3.3 V, V_NO, V_NC = V_COM = 0.3 V/3 V
Room - 1
Full
- 10
1
10
Digital Control
Input High Voltage
Input Low Voltage
Input Capacitance^d
Input Current
V_INH
V_INL
C_in
I_INL or I_INH
V_IN = 0 or V+
Full
1.4
Full
V
0.5
Full
5
pF
Full
-1
1
µA
Dynamic Characteristics
Turn-On Time
Turn-Off Time
Charge Injection^d
Off-Isolation^d
NO, NC Off Capacitance^d
Channel-On Capacitance^d
t_ON
t_OFF
Q_INJ
OIRR
C_NO(off)
C_NC(off)
C_ON
V_NO or V_NC = 1.5 V, R_L = 50 , C_L = 35 pF
Figure 1
C_L = 1 nF, V_GEN = 0 V, R_GEN = 0 , figure 3
R_L = 50, C_L = 5 pF, f = 1 MHz
V_IN = 0 or V+, f = 1 MHz
Room
Full
Room
Full
Room
Room
Room
Room
17
29
ns
14
26
9
pC
- 57
dB
72
pF
92
Power Supply
Power Supply Range
V+
1.5
3.6
V
Power Supply Current
I+
V+ = 3.6 V, V_IN = 0 or V+
0.01 1.0 µA
Notes:
a. Room = 25 °C, Full = as determined by the operating suffix.
b. The algebraic convention whereby the most negative value is a minimum and the most positive a maximum, is used in this data sheet.
c. Typical values are for design aid only, not guaranteed nor subject to production testing.
d. Guarantee by design, nor subjected to production test.
e. V_IN = input voltage to perform proper function.
f. Guaranteed by 3 V leakage testing, not production tested.
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation
of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum
rating conditions for extended periods may affect device reliability.
Document Number: 72740
S11-0303-Rev. C, 28-Feb-11
www.vishay.com
3