6N138_08 Datasheet, PDF (3/6 Pages) Vishay Siliconix – High Speed Optocoupler, 100 kBd, Low Input Current, Photodiode Darlington Output

6N138/6N139
Vishay Semiconductors ^{High Speed Optocoupler, 100 kBd,}
Low Input Current, Photodiode Darlington
Output
ELECTRICAL CHARACTERISTICS ⁽¹⁾
PARAMETER
TEST CONDITION
PART SYMBOL MIN.
TYP.
MAX.
UNIT
OUTPUT
Logic low, output voltage ⁽²⁾
Logic high, output current ⁽²⁾
Logic low supply current ⁽²⁾
Logic high supply current ⁽²⁾
COUPLER
I_F = 1.6 mA, I_O = 4.8 mA,
V_CC = 4.5 V
I_F = 1.6 mA, I_O = 8.0 mA,
V_CC = 4.5 V
I_F = 5.0 mA, I_O = 15 mA,
V_CC = 4.5 V
I_F = 12 mA, I_O = 24 mA,
V_CC = 4.5 V
I_F = 0 mA, V_CC = 7.0 V
I_F = 0 mA, V_CC = 18 V
I_F = 1.6 mA, V_O = OPEN,
V_CC = 18 V
I_F = 0 mA, V_O = OPEN,
V_CC = 18 V
6N138
6N139
6N139
6N139
6N138
6N139
V_OL
V_OL
V_OL
V_OL
I_OH
I_OH
I_CCL
I_CCH
0.1
0.4
V
0.1
0.4
V
0.15
0.4
V
0.25
0.4
V
0.1
250
µA
0.05
100
µA
0.2
1.5
mA
0.001
10
µA
Input capacitance
Input output insulation leakage
current ⁽³⁾
Resistance (input to output) ⁽³⁾
Capacitance (input to output) ⁽³⁾
f = 1.0 MHz, V_F = 0
45 % relative humidity,
T_amb = 25 °C, t = 5.0 s,
V_IO = 3000 VDC
V_{IO =} 500 VDC
f = 1.0 MHz
C_IN
25
pF
1.0
µA
R_IO
10¹²
Ω
C_IO
0.6
pF
Notes
(1) _{Tamb = 25 °C, unless otherwise specified. Minimum and maximum values are testing requirements. Typical values are characteristics of the}
device and are the result of engineering evaluation. Typical values are for information only and are not part of the testing requirements.
(2) _{Pin 7 open.}
(3) _{Device considered a two-terminal device: pins 1, 2, 3 and 4 shorted together and pins 5, 6, 7, and 8 shorted together.}
CURRENT TRANSFER RATIO
PARAMETER
TEST CONDITION
PART SYMBOL MIN.
TYP.
MAX.
Current transfer ratio ⁽¹⁾⁽²⁾
Current transfer ratio
I_F = 1.6 mA, V_O = 0.4 V,
V_CC = 4.5 V
I_F = 0.5 mA, V_O = 0.4 V,
V_CC = 4.5 V
I_F = 1.6 mA, V_O = 0.4 V,
V_CC = 4.5 V
6N138 CTR
300
1600
6N139 CTR
400
1600
6N139 CTR
500
2000
Notes
(1) _{DC current transfer ratio is defined as the ratio of output collector current, IO, to the forward LED input current, IF times 100 %.}
(2) _{Pin 7 open.}
SWITCHING CHARACTERISTICS
PARAMETER
TEST CONDITION
PART
Propagation delay time to logic
low at output
Propagation delay time to logic
low at output ⁽¹⁾⁽²⁾
Propagation delay time to logic
high at output
Propagation delay time to logic
high at output ⁽¹⁾⁽²⁾
I_F = 1.6 mA, R_L = 2.2 kΩ
I_F = 0.5 mA, R_L = 4.7 kΩ
I_F = 12 mA, R_L = 270 Ω
I_F = 1.6 mA, R_L = 2.2 kΩ
I_F = 0.5 mA, R_L = 4.7 kΩ
I_F = 12 mA, R_L = 270 Ω
6N138
6N139
6N139
6N138
6N139
6N139
Notes
(1) _{Pin 7 open.}
(2) _{Using a resistor between pin 5 and 7 will decrease gain and delay time.}
SYMBOL
t_PHL
t_PHL
t_PHL
t_PLH
t_PLH
t_PLH
MIN.
TYP.
2.0
6.0
0.6
2.0
4.0
1.5
MAX.
10
25
1.0
35
60
7.0
UNIT
%
%
%
UNIT
µs
µs
µs
µs
µs
µs
www.vishay.com
186
For technical questions, contact: [e-mail]
Document Number: 83605
Rev. 1.5, 07-May-08